Paxton Superchargers Mustang Novi 1220 - Manual (Page 17)

P/N: 4809631
©2007 Paxton Automotive
All Rights Reserved, Intl. Copr. Secured
23MAY07 v1.0 Template(4809631v1.0)
6-1
6.0 MAIN BRACKET ASSEMBLY
Fig. 6.0-a
Assemble the main bracket, plate and other parts neces-
sary to relocate the alternator and smog pump and make
room for the supercharger. For 1992 and later vehicles,
please review points “A” through “H” before starting.
A. Measure the length of the pivot boss on the
alternator and record. It should be very close
to 3".
B. In a similar manner, measure the boss on the
smog pump. When combined with the .920"
spacer, it should be 4.050". Record these
measurements so that in the event of a belt
alignment problem, Paxton can properly
advise you.
C. Place the smog pump and alternator on the
large aluminum mounting bracket as shown.
After making sure the 6-1/4" bolts have wash-
ers on them, enter the cast mounting bracket
from the rear (coming towards you). Place the
.920" tube spacer over the bolt on the smog
pump. Lower supercharger mounting plate
over bolts. The idea is to sandwich the alter-
nator and smog pump between the mounting
bracket and plate. Place washers and nuts on
the 6-1/4" bolts and finger tighten. For vehi-
cles equipped with alternators having larger
7/16" pivot bolts, it will be necessary to
enlarge the corresponding hole in the plate.
D. Start the 3/8-16 x 1" fastener with a washer at
the top of the bracket and finger tighten.
Insert the 6-1/2" and 7" bolts. These bolts will
later hold the assembly to engine.
*** NOTE ***
Remember to place the .920" spacer between the
smog pump and mounting plate.
3/8-16x1"
MOUNTING PLATE
MOUNTING BRACKET
3/8-16X1-3/4"
7/16-14 x 1-3/4"
3/8-16 x 6-1/2"
3/8-16 x 7"
3/8-16 x 6-1/4"
install from rear
ALTERNATOR
ALTERNATOR STAY
3/8-16 x 1"
3/8-16 x 3/4"
3/8-16 x 2"
3/8-16 x 6 1/4"
install from rear
place .920" spacer
between plate & pump
SMOG PUMP
& PULLEY
3/8-16 x 6 1/4”
install from rear
and place .920 spacer
between plate and pump
3/8-16 x 1 3/4”
(6-3/4” *)
(7-1/4” *)
3/8-16 x 6 1/4”
install from rear
and place .920 spacer
between plate and pump
3/8-16 x 1 3/4”
3/8-16 x 6 1/4”
install from rear
and place .920 spacer
between plate and pump
3/8-16 x 1 3/4”
Section 6
MAIN BRACKET ASSEMBLY
E. Attach the Paxton alternator brace between
the boss on the smog pump and alternator
with the 3/8-16 x 1" bolts. On 1992 and later
Mustangs, it may be necessary to drill and tap
the “blanked” hole in the smog pump. To
accomplish this use an “R” size bit and a 3/8-
16 size tap.
F. Tighten all fasteners in the bracket/accessory
assembly.
G. Lower the entire assembly into position and
start all four fasteners that hold it to the
engine. Tighten all fasteners in a progressive
manner.
H. Reconnect alternator wires and use a tie-wrap
to secure the wires.