Flowserve ME - Manual (Page 35)

ME USER INSTRUCTIONS ENGLISH 71576287 - 02/13
Page 35 of 36 flowserve.com
8.2 Sectional drawings part list
ITEM DESIGNATION ITEM DESIGNATION
1110 Pump casing 4200 Mechanical seal
1221 Casing cover 4590-01 Gasket
1221-01 Casing cover 4590-02 Gasket
1221-02 Casing cover 4590-03 Gasket
1500-01 Wear ring 4610-01 O-ring
1500-02 Wear ring 4610-02 O-ring
2110 Pump shaft 6511 Priming plug
2250
Radial flow impeller
shrouded
6515 Drain plug
2450 Shaft sleeve 6541 Lockwasher
2450-01 Shaft sleeve 6544 Circlip
2540 Thrower 6544-01 Circlip
2905 Washer 6544-02 Circlip
2905-01 Washer 6569 Screwed plug
2905-02 Washer 6572 Stud
2912 Impeller nut 6572-01 Stud
3011 Radial ball bearing 6572-02 Stud
3012
Radial roller
bearing
6572-03 Stud
3126 Shim 6577-01 Hexagon head bolt
3134 Support foot 6577-02 Hexagon head bolt
3200 Bearing housing 6577-03 Hexagon head bolt
3260 Bearing cover 6581 Hexagon nut
3260-01 Bearing cover 6581-01 Hexagon nut
3260-02 Bearing cover 6581-02 Hexagon nut
3712 Bearing nut 6581-03 Hexagon nut
3853 Grease nipple 6581-04 Hexagon nut
3863 Grease regulator 6700-01 Coupling key
4120 Gland 6700-02 Impeller key
4130 Gland packing 9331 Cover plate
8.3 General arrangement drawing
The typical general arrangement drawing and any
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the
User Instructions. If required, copies of other
drawings sent separately to the Purchaser should
be obtained from the Purchaser and retained with
these User Instructions.
9 CERTIFICATION
Certificates determined from the Contract
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for
retention with these User Instructions.
10 OTHER RELEVANT
DOCUMENTATION AND MANUALS
10.1 Supplementary User Instructions
Supplementary instructions such as for a driver,
instrumentation, controller, seals, sealant system
etc are provided as separate documents in their
original format. If further copies of these are
required they should be obtained from the supplier
for retention with these User Instructions.
10.2 Change notes
If any changes, agreed with Flowserve, are made to
the product after its supply, a record of the details
should be maintained with these User Instructions.
10.3 Additional sources of information
Reference 1:
NPSH for Rotor dynamic Pumps: a reference
guide, Euro pump Guide No. 1, Euro pump &
World Pumps, Elsevier Science, United Kingdom,
1999.
Reference 2:
Pumping Manual, 9
th
edition, T.C. Dickenson,
Elsevier Advanced Technology, United Kingdom,
1995.
Reference 3:
Pump Handbook, 2
nd
edition, Igor J. Karassik et al,
McGraw-Hill Inc., New York, 1993.
Reference 4:
ANSI/HI 1.1-1.5, Centrifugal Pumps -
Nomenclature, Definitions, Application and
Operation.
Reference 5:
ANSI B31.3 - Process Piping.