GAI-Tronics 701-307ICS ICS DC-Powered Page/Party Plug-in Amplifiers User Manual

Ics dc-powered page/party, Plug-in amplifiers - quick installation guide, Important safety instructions

Advertising
background image

Pub. 42004-731L2BQG

GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA

610-777-1374

„ 800-492-1212 „ Fax: 610-796-5954

V

ISIT WWW

.

GAI

-

TRONICS

.

COM FOR PRODUCT LITERATURE AND MANUALS

G A I - T R O N I C S ® C O R P O R A T I O N

A H U B B E L L C O M P A N Y

ICS DC-Powered Page/Party

®

Plug-in Amplifiers - Quick Installation Guide

Important Safety Instructions

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, Class II Division 2, Groups F, and G, Class III OR non-hazardous locations only.
Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

Read, follow, and retain instructions – All safety and operating instructions should be read and followed before operating the unit. Retain instructions for future
reference.

Heed warnings – Adhere to all warnings on the unit and in the operating instructions.

Attachments – Attachments not recommended by the product manufacturer should not be used, as they may cause hazards. Maximum system cable length is not to
exceed two miles.

Servicing – Do not attempt to service this unit by yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.

WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous. Averttissement –
Risque d’explosion – avant de déconnector l’equipment, couper le courant ou s’assurer que l’emplacement est désigné non dandereux.

USA and Canada Consult the National Electrical Code (NFPA 70), Canadian Standards Association (CSA 22.1), and local codes for specific requirements regarding
your installation. Class 2 circuit wiring must be performed in accordance with NEC 725.55.

WARNING

In 24 V dc systems: Under NO condition should this equipment be operated from a battery charger without the batteries connected.

In 24 V dc systems, most chargers have an unloaded output of 35 to 45 volts that can quickly damage the equipment designed for nominal 24 volts. The maximum
battery voltage should never exceed the maximum specified input voltage.

General Information and Available Options

This quick

guide covers the installation of the ICS DC-Powered Plug-in Amplifiers. See the chart below for applicable models.

ICS Amplifier
Model


Description

751-002ICS Speaker

Amplifier

701-307ICS Handset/Speaker

Amplifier

701-309ICS

Handset/Speaker Amplifier with
Auxiliary Jack

751-002ICSVC

Speaker Amplifier with VLC

701-307ICSVC

Handset/Speaker Amplifier with VLC

701-309ICSVC

Handset/Speaker Amplifier with
Auxiliary Jack and VLC

751-902ICS SmartSeries

Speaker

Amplifier

701-907ICS SmartSeries

Handset/Speaker

Amplifier

701-909ICS SmartSeries

Handset/Speaker

Amplifier with Auxiliary Jack

Figure 1. ICS DC-Powered Page/Party

®

Plug-in Amplifier Installation


Refer to Pub. 42004-731L2 at the “Manuals & Specs” link at

www.gai-tronics.com

for detailed explanations of the available models

and their settings, adjustments and warranty.

Installing the ICS Page/Party

®

Plug-in Amplifier

1. Plug the amplifier directly into the enclosure. Use extra care not to damage the protruding latch wings of connector P6 located on

the top right edge of the amplifier during installation.

2. Attach the amplifier to the enclosure with the hardware provided. See Figure 1.

3. Apply power to the station.

Advertising