Harken 3852 System B CB & Slider Battcars: built 2007 to present - Manual (Page 2)

Part No. Description Includes
3845, 3846 Track Mounting Kit (a) 19 mounting slugs 7/8" (22mm); (b) 1 connector slug 3" (76mm); (c) 2 Tubes Blue Loctite®; (d) 21 HFS321 Flathead screws 6 x 20mm.
3847
3848
Screwpin
Endstop Kit
(c) 1 tube blue Loctite®; (f) 1 top stop slug 17/16" (36mm); (g) 3 HFS321 flathead screws 6 x 20mm; (h) 2 HFS1037 flathead screws 6 x
30mm; (i) 2 mounting slugs 7/8" (22mm); (j) 1 top endstop 1522A; (k) pin stop; (l) 1 end track
3850, 3851 Endstop Kit (c) 1 tube blue Loctite®; (f) 2 stop slugs 17/16" (36mm); (h) 4 HFS1037 flathead screws 6 x 30mm; (j) 2 endstops 1522A
3844 Track (slug type) Section length: 6'91/8" (2.06m). Number of track sections depends on luff length of your mainsail.
1616 Track (drill and
tap type)
Use for masts without grooves or when slugs will not fit. Purchase stainless steel 1/4" (6mm) screws separately.
Do not use 3844 track. It requires mounting slugs. See page 8 for drill/tap sizes and mounting instructions.
Track Mounting Kit
3845, 3846
a
b
c
d
Track and Accessories
CB System
Part No.
Slider System
Part No. Description Comments
3852 3833 Headboard cars 3852 must use 3861 or 3862 headboard.
3863 3836 Intermediate cars If battens are close enough intermediate cars are not needed.
3856 3834 Batten car 10mm Threaded stud. Purchase batten receptacle separately.
3857 3835 Batten car 12mm Threaded stud. Purchase batten receptacle separately.
3859 — Universal Battcar Purchase batten receptacle and threaded stud separately.
3860 — Reef Tack car Double up track screws at reefed car position.
CB/Slider Parts
CB/Slider Systems Parts List
3856/3857 – CB
3834/3835 – Slider
Batten Cars without Receptacles
Intermediate
Cars
3836 Slider
3863 CB
Universal Battcar
3859 – CB
3860 – CB
Reef Car
Thank you for puchasing Harken's B Battcar system. Please read manual before assembling system.
2 System B (CB/Slider) 11-14-08
1616
3844
9 /
16
"
(14mm)
1 1 /
16
" (27mm)
Track
(Mounting Slug Type)
Track
(Drill and Tap Type)
1 1 /
16
" (27mm)
CB System
Part No. Description Comments
3861 Standard web-on headboard See sailmaker instructions, page 12 - 14
3862 Square top web-on headboard See sailmaker instructions, page 12 - 14
CB System Parts
3852
CB
3833
Slider
Headboard Cars (Assembly)
3861
CB–Web-On
Standard
3862
CB Web-On
Square Top
Headboard Cars (Assembly)
c
Endstop Kits
3850, 3851
j
h
f
l
i
Screwpin Endstop Kits
3847,3848
f
k
g
h
c
j
1. Tape measure 6. Hammer 11. File
2. Allen wrench 5mm 7. Hacksaw 12. Nut driver 10mm
or open/box-end
wrench
3. Power drill (screwdriver) 8. Center punch
4. Drill bit -
17 / 64 " (6.5mm) 9. Tape
5. Phillips screwdriver 10. Putty knife
Mast-up installation: stepladder secured to boat
Work height: 7' (2.13m) above boom
1
6
8
3
9
9
11
2
10
4
Tools You Will Need:
7
12
Slider Cars
Only
5