How to use this instruction manual, What you should know before you begin, What you need to get started – InSinkErator Invite H-Contour-SS User Manual

Page 2: Overview of a completed setup, Equipment you may need, Equipment required

Advertising
background image

Unpack dispenser components.
On a firm, flat surface, carefully

straighten the copper tubing using

hands only.

View/Wave

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

InstallIng the faUcet - VIew/waVe

a

hOw tO Use thIs InstRUctIOn ManUal

these instructions are separated into main sections, indicated by numbers, and subsections,

indicated by capital letters. the manual is setup this way to allow you to take a break at any

point after completing a section or subsection without affecting the installation process.

what you’ll see in the

instruction manual:

OVeRVIew Of a

cOMPleteD setUP

H-Contour-SS

H-Classic-SS

H-View-SS

H-Wave-SS

HC-View-SS

HC-Wave-SS

Identify the model of your instant hot water dispenser and record it here:______________________

1

2

equipment You May need:

we are delighted that you have chosen the Insinkerator

®

Instant hot water Dispenser to be

a part of your home. this unique appliance will save you time and effort in the kitchen, and

you’ll enjoy discovering new uses for it each day. that’s exactly why millions of people are

now using an Insinkerator Instant hot water Dispenser.
we are confident that by following our step-by-step instructions, you’ll soon be enjoying the

convenience of instant hot water.

For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this

instant hot water dispenser.
This particular unit is not intended for commercial use.

Make sure that all electrical wiring and connections conform to local codes.
A standard 115-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.
The wall outlet powering your dispenser must have power supplied to it continuously.
This outlet must be fused and should not be controlled by the same wall switch that operates the disposer,

unless you have a SinkTop Switch

from InSinkErator

®

.

It is recommended that a dedicated control valve be installed on the cold water line supplying water to this

system.

If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation

of this unit, it is recommended to use our water filtration system.
This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the

number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty

water discharged from the hot water dispenser may indicate the need for service or replacement of this product.

The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).

If it does, this will prevent your unit from operating properly.

Moving parts inside the tank causing a rattling noise is normal.

what YOU shOUlD KnOw BefORe YOU BegIn

equipment Required:

n

Drill

n

t-fitting

n

Dedicated control valve

n

adjustable wrench

n

Phillips and flat blade screwdrivers

n

Pencil

n

tape Measure / Ruler

n

level

anchors for drywall
hole saw

Basin wrench
hole punch

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench

and a 1/8" plug or a 1/4" cap (

not supplied) for the faucet spray hose line. See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 1-1/4" – 1-1/2" hole

saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a

surface other than stainless steel.

what YOU neeD tO get staRteD

3

2

Provides a step-by-step narrative describing the installation step, with check boxes that

can be marked as you progress through the installation.

contains simple illustrations that provide visual instruction to support the narrative.

Important safety messages that will require your attention during the step.

1

2

3

Warning indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

Caution indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

Notice is used to address practices not related to personal injury.

NOTICE

NOTICE

NOTICE

To see a tutorial of this installation:
http://goo.gl/AZOHu

NOTICE

3

Advertising
This manual is related to the following products: