Document Outline

• CONTENT
• 1. Introduction
  • Chapter Structure
  • How to Use This Manual
  • Terms and Definitions
  • System Overview
  • Application Questions
• 2. Hardware Orientation
  • In This Chapter
  • VSP 628PRO Back Panel
    • CONT Interface
      • 1: 10/100M UDP Interface
      • 2: USB Interface
    • INPUT Interface
      • 3: Genlock Input
      • 5.7: 3G-SDI Input
      • 11: DVI Input
      • 13: HDMI Input
      • 15: Displayport Input
      • 16: VGA Input
      • 4: Genlock Loop Out
      • 6.8: 3G-SDI Loop Out
      • 12: DVI Loop Out
      • 14: HDMI Loop Out
    • OUTPUT Interface
      • 17: DVI Output
      • 18: HDMI Output
      • 19: VGA Output
      • 20：CVBS Output (OC Optional Module)
    • Switch and Power
      • 21.22: Power Interface and Switch
    • Optional Module
    • 9: S. V. D. H. U. C. HDMI_DP_4K2K_IN Optional Module
    • 10: F. S Optional Module/Sending Card Interface
    • Interface Protection Block
  • VSP 628PRO Front Panel
    • OLED Panel
    • Menu Buttons
    • Signal keys
    • Function
• 3. Hardware Installation
  • In This Chapter
  • Safety Precautions
  • Unpacking and Inspection
  • Site Preparation
• 4. Menu Orientation
  • In This Chapter
  • MENU
    • Input
    • Output
    • Custom Formats
    • Views
    • Transition
    • System
    • Logo
    • Display Setup
    • Test Pattern
    • Tech Support
    • Factory Reset
• 5. Communication Software Guideline
  • In This Chapter
  • Software Installation
  • Softwar e Operation
    • Set up Communication
    • Use
      • Image Toolbar
      • Signal Select
      • Scale
      • Mode
      • Output
      • Input
      • Layer
      • Save
      • Load
      • Other
• 6. System Setup and Operations
  • In This Chapter
  • Interface and Input Signal Option
  • How to Realize the System Mode Setting
    • 1. Standard
      • Single Image Switching
      • PIP Setting
      • Scale Setting
      • Image Size Adjust
      • Dimmer and Effects Setting
    • 2. Dual 2K Setting
    • 3. Switcher Setting
    • 4. Split
    • 5. MinDelay
  • How to Do Customized Output Resolution
  • How to Realize the Test Pattern Setting
  • How to Realize LAN Remote Control Setting
  • How to Realize WEB SERVER Cross-platform setting
  • How to Save the Parameter
  • How to Load the Saved Parameter
• 7. Common Questions and Solution
  • In This Chapter
  • OLED Screen prompts "No Core Board"
    • Confirm if there are any input signals
    • Confirm If the Core Board is Loose
  • No Display on LED Display when Output HDMI to Sending Card
    • Set DVI for HDMI Output Format
  • Flash Point on LED Display when Output
    • Add the Long-term Signal Amplify Module
  • APP Software cannot Properly Connected in Mobile Phone or Tablet Computer
    • Confirm if the Device Install the Web Server Module
    • Confirm if the Web Server Module Driver is Normal
    • Confirm if IP Conflict for Mobile Phone, Wireless Router and Device
  • VGA Input Offset or cannot be Full Size Shown
    • Set Auto Adjust for VGA Input
  • Software Upgrade Failed
    • Failed when Upgrade to 90%
    • EDID Package Upgrade Failed
• A. Specification
• B. Contact Information
• C. Software Upgrade
• D. WEB SERVER Cross-platform Control Operation Interface
• E. VSP 628PRO Connect APP Control Operation
• F. Optional Module Installation and
• Replacement Instruction