Smithco Super Star 42-00x (sn 4602 – 4660/12588 – 12627) Parts & Service Manual - Manual (Page 73)

71
Accessories
42-750 CART PATH AND SIDEWALK EDGER PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 HCP-12-200 Clevis Pin, 1 /
2
x 2 2
2 HHP-18 Bridge Pin, 1 /
8
4
3 HCP-58-250 Clevis Pin, 5 /
8
x 2 1 /
2
1
4 42-203 Attachment Lift Assembly 1
5 42-758 Brush 1
6 42-754 Edger Mount 1
7 HB-38-16-125 Bolt, 3 /
8
-16 x 1¼ 3
HNFL-38-16 Flange Whiz-Lock Nut, 3 /
8
-16 3
HW-38 Flat Washer, 3 /
8
3
8 HG-14-28-180 Grease Fitting, 1 /
4
- 28 x 180°( Part of 42-755 ) 1
9 42-755 Edger Arm 1
10 10-134 Spacer 1
11 HB-38-16-250 Bolt, 3 /
8
- 16 x 2½ 3
HNFL-38-16 Flange Whiz-Lock Nut, 3 /
8
-16 3
HW-38 Flat Washer, 3 /
8
1
12 60-123 Shock Absorber 1
13 HW-38 Flat Washer, 3 /
8
4
14 48-109 Spring 1
15 42-757 Spring Mount 1
16 HNTL-34-16 Lock Nut, ¾ - 16 1
17 HMB-34-10 Machine Bushing, ¾ x 10GA 2
18 42-756 Edger Fork 1
19 HB-58-11-325 Bolt, 5 /
8
- 11 x 3¼ 1
HNCL-58-11 Center Lock Nut, 5 /
8
-11 1
20 76-298 Spacer 2
21 42-752 Edger Blade 1
22 42-759 Brush Holder 1
23 HB-14-20-075 Bolt, ¼ - 20 x ¾ 3
HNFL-14-20 Flange Whiz-Lock Nut, ¼ - 20 3
24 HMB-100-14 Machine Bushing, 1 x 14GA 2
INSTALLATION INSTRUCTIONS
For your convenience and ease of installation, a major set of components are pre-assembled at the
factory. This is the "Edger Assembly" and includes Reference #'s 11 thru 23.
1. Slide attachment lift assembly (Ref 4) under machine and attach using (2) ½ x 2" clevis pins and 1 /
8
"
bridge pins (Ref 1 and 2). Connect the free end of the hydraulic cylinder to the attachment liftaAssembly
(Ref 4) as illustrated using the
5 /
8
x 2½ clevis pin and
1 /
8
" bridge pin (Ref 3 and 2).
2. Attach the edger mount (Ref 6) to the attachment lift assembly (Ref 4) using (3) 3 /
8
- 16 x 1¼ bolts,
3 /
8
flat
washers & 3 /
8
-16 whiz-lock nuts (Ref 7).
3. Now slide (1) 1" machine bushing (Ref 24) on the edger mount's (Ref 6) pin. Next install the "Edger
Assembly" (see sidebar) onto the pin. Place the second 1" machine bushing (Ref 24) on the pin. Secure
with a
1 /
8
" ridge pin (Ref 2).
4. Slide (1) 3 /
8
" flat washer onto (1) 3 /
8
- 16 x 2½ bolt & insert this in the free end of the shock absorber (Ref
12). Next, slide the spacer (Ref 10) onto the bolt and use (1) 3 /
8
-16 whiz-lock nut to secure the shock
absorber (Ref 12) to the edger mount (Ref 6) as illustrated.
5. Grease all grease fittings (Ref 8) and check all fasteners for proper installation.