Teac US-2000 - Manual (Page 19)

TASCAM US-2000
19
Input/output ratings
Analog audio input/output
MIC INPUTS (Balanced) terminals (1-8)
Connector: XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance: 2.4 kΩ
Nominal input level:
–60 dBu (When input gain konb is at maximum )
–4 dBu (When input gain knob is at minimum)
Maximum input level:
+12 dBu (When input gain knob is at minimum)
INST IN (Unbalanced) terminals (7-8)
Connector: 6.3 mm (1/4”) Standard phone jack
Input impedance: 1 MΩ
Nominal input level:
–56 dBu (When input gain konb is at maximum )
0 dBu (When input gain knob is at minimum)
Maximum input level:
+16 dBu (When input gain knob is at minimum)
LINE IN (Balanced) terminals (9-14)
Connector: 6.3 mm (1/4”) TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Input impedance: 10 kΩ
Nominal input level:
–10 dBV/+4 dBu
Maximum input level:
+6 dBV/+ 20 dBu
LINE OUTPUTS (Balanced) terminal
Connector: 6.3 mm (1/4”) TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
+4 dBu
Maximum output level:
+20 dBu
MONITOR OUT (Balanced) terminal
Connector: 6.3 mm (1/4”) TRS Standard phone jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
+4 dBu
Maximum output level:
+20 dBu
INSERT (Unbalanced) terminal
Connector: 6.3 mm (1/4”) TRS Standard phone jack
(Tip: SEND, Ring: RECEIVE, Sleeve: GND)
Output impedance: 100Ω
Nominal output level:
–2 dBu
Maximum output level:
+14 dBu
Input impedance: 10 kΩ
Nominal input level
–2 dBu
Maximum input level:
+14 dBu
PHONES jack
Connector: 6.3 mm (1/4”) Standard Stereo phone jack
Maximum output level:
100 mW + 100 mW or more
(THD + N less than 1%, 32Ω load)
Digital audio input/output
DIGITAL IN (COAXIAL) terminal
Connector: RCA pin jack
Compatible signal format: IEC60958-3 (S/PDIF)
DIGITAL OUT (COAXIAL) terminal
Connector: RCA pin jack
Compatible signal format: IEC60958-3 (S/PDIF) or
AES3-2003 (AES/EBU), selectable using control panel
Control input/output
USB terminal
Connector: USB B type 4 pin
Format:
USB 2.0 High speed (480 MHz)
Audio performance
Frequency response
20 Hz - 20 kHz, ±1.0 dB (44.1/48 kHz) ( MIC to
MONITOR OUTPUT )
20 Hz - 40 kHz, +0.5/–2.0 dB (88.2/96 kHz) ( MIC to
MONITOR OUTPUT )
Signal-to-noise ratio
90 dB ( LINE IN to MONITOR OUTPUT , 20 kHz LPF +
A-weighted)
Total harmonic distortion
Less than 0.01% ( LINE IN to MONITOR OUTPUT , 1 kHz,
+20 dBu input, 20 kHz LPF)
Computer requirements
Windows
Supported Operating system
Windows:
Windows XP 32 bit SP2 or later
Windows XP 64 bit SP2 or later
Windows Vista 32 bit SP2 or later
Windows Vista 64 bit SP2 or later
8 – Specifications