Elecom WRH-150xx 設定手順書（他言語版） - Manual

-1-
步骤
Preparation
Windows 8
Connect the LAN cable to the LAN port in your hotel room
and to this product's WAN port.
Connect the USB cable to this product's power supply jack, and then
use one of the following methods to supply power to the product.
If you will use a PC's USB port, proceed to step .
If you will use the USB-type AC adapter, proceed to step .
Install this product's built-in wired LAN adapter driver.
Windows
Wait until the PC has completed its startup procedure, and
then connect this product to the PC's USB port.
The "AutoPlay" dialogue box is displayed automatically.
Click "Run Setup.exe."
Mac OS
Click the [Apple menu] in the upper left of the screen, and
then click [System Preferences].
Click [Network].
Set "Interface" to "USB Network Interface," and then click
[Create].
On the "Network" screen, click "Apply," and check that the
status has changed from "Not Configured" to "Connected."
Click [+] (addition) in the lower left of the screen.
Check the status of this product's lamps.
Procedure Connection
Point to the upper-right corner of the screen to display the
Charms bar, and then click [Settings].
From the list of networks, select the network that has the
same SSID as the network written on the included "Setup
Information Sheet," and then click [Connect].
Check that the message "You can also connect by pushing
the button on the router." is displayed.
Click the wireless icon .
Hold down the product's [WPS and reset] button for
approximately 3 seconds. When you release the button, the
product's "WPS and reset lamp" will start to blink in blue.
If a screen is displayed with the message "Do you want to turn
on sharing between PCs and connect to devices on this
network?," click "Yes, turn on sharing and connect to devices."
B Windows 7/Vista/XP
Click the wireless LAN icon in the notification area in the
lower-right corner of the screen.
From the list of networks, select the network that has the
same SSID as the network written on the included "Setup
Information Sheet," and then click [Connect].
When the "Connect to a Network" dialogue box is
displayed, check that the message "You can also connect
by pushing the button on the router." is displayed.
Hold down the product's [WPS and reset] button for
approximately 3 seconds. When you release the button, the
product's "WPS and reset lamp" will start to blink in blue.
Eventually, the "Connect to a Network" dialogue box will
disappear automatically.
C Mac OS
Click the [Apple menu] in the upper left of the screen, and
then click [System Preferences].
Click [Network].
Check that "Status" for the AirMac has changed to "On."
From the list of networks, select the network that has the
same SSID as the network written on the included "Setup
Information Sheet."
A password entry screen will be displayed, so enter the
(13-digit) encryption key written on the "Setup Information
Sheet," and then click [OK].
Depending on the hotel, the web browser (such as IE and Safari) may require you to
certify yourself. In this situation, check with the hotel regarding how to certify yourself.
From your terminal, open the AppStore (iOS) or Google Play
(Android), search for [QR link], and then install the software.
On your terminal's home screen, tap the [QR link]
icon.
Follow the instructions on the screen, and then tap [Close]
to finish the procedure.
Tap [Read QR Code] to read the QR code printed on the
included "Setup Information Sheet."
Install the simple setup application "QR link" (free of charge), and
then configure the settings.
D Smartphones and tablet PCs
(iOS/Android)
* On Windows XP, if the "Found New Hardware Wizard" screen is displayed,
click [Cancel].
If a message stating "Found New Hardware" is displayed on the screen, open
the "Setup" drive from My Computer, and then click "Setup.exe" to proceed
with the installation.
Names and Functions of Parts
Top Front Back Left side Right side
Bottom
WRH-150x Simple Manual
Power supply
jack (Micro USB)
Connect a cable that conforms to the USB 2.0 (Micro-B
to Micro-A) standard.
WAN port (blue) Use a LAN cable to connect this product to the hotel's LAN port.
WPS and reset
lamp (blue)
Lit The reset function is starting.
Blinking The WPS function is in operation.
The product is operating normally.
WAN lamp
(blue)
Lit or blinking The connection with the WAN side is being established.
The product is disconnected from the WAN side.
WAN lamp
(blue)
Lit or blinking The connection with the wireless side
is being established.
The product is disconnected from the wireless side.
WPS and reset
button
Hold down this button for approximately 1 to 9 seconds to
start the WPS function.
Hold down this button for 10 seconds or more to start the reset
function.
This item refers to a procedure that is only necessary the first
time that you connect this product to a PC.
Mac OS
WPS and reset lamp
WAN lamp
Lit in blue or blinking in blue
WAN lamp Lit in blue or blinking in blue
Procedure
准备
Windows 8
用 LAN 电缆连接酒店客房的 LAN 端子和本产品的 WAN 端
口。
USB 电缆连接到本产品的电源插孔，然后用以下的任一方法
接通电源。
使用电脑的 USB 端口的用户，请进入 。
使用 USB 型 AC 适配器的用户进入 。
安装本产品内置的有线局域网适配器的驱动程序。
使用Windows
待电脑完全启动后，将本产品连接到电脑的 USB 端口。
自动弹出“ 自动播放 ”窗口后，点击“ 执行 Setup.exe ”。
Mac OS
点击屏幕左上方的［苹果菜单］，点击［系统环境设置］。
点击［网络］。
在“ 界面 ”项，选择“USB Network Interface”并点击［创建］。
点击“ 网络 ”窗口的“ 应用 ”，确认状况从“ 状况不明 ”
变为“ 已连接 ”。
点击屏幕左下方的［＋（增加）］。
检查本产品指示灯的状态。
连接
将鼠标器放到屏幕右上角，出现超级按钮栏，点击［设置］。
从网络列表中选择与附带的“ 设置信息表 ”上所记载的相
同的 SSID，并点击［连接］按钮。
确认“ 按下路由器的按钮也无法连接。”的消息。
点击无线的图标 。
长按本产品的［WPS/Reset 按钮］3 秒钟左右然后放开，本产
品的“WPS/Reset 指示灯 ”开始蓝色闪烁。
弹出“ 启用电脑共享 ...”窗口后，点击“ 是，启用共享并连
接到设备 ”。
B Windows 7/Vista/XP
点击屏幕右下方任务栏上的无线局域网的图标。
从网络列表中选择与附带的“ 设置信息表 ”上所记载的相
同的 SSID 并点击［连接］按钮。
弹出“ 连接网络 ”的窗口后，确认“ 按下路由器的按钮也
无法连接。”的消息。
长按本产品的［WPS/Reset 按钮］3 秒钟左右后放开，本产品
的“WPS/Reset 指示灯 ”开始蓝色闪烁。
不久， “ 连接网络 ”窗口自动关闭。
C Mac OS
点击屏幕左上方的［苹果菜单］，点击［系统环境设置］。
点击 [ 网络 ]。
确认 AirMac 的“ 状况 ”为“ 启用 ”。
从“ 网络名称 ”列表中选择与附带的“ 设置信息表 ”上所
记载的相同的 SSID 。
弹出密码输入窗口，输入“ 设置信息表 ”所记载的密钥（13
位数）并点击［确定］。
有些酒店可能需要用Web浏览器（IE或Safari等）进行认证，如果需要认证，请向
您下榻的酒店确认认证方法。
从智能手机或平板电脑打开 AppStore（iOS）或 Google Play
（Android），搜索［QR link］并安装。
触摸智能手机或平板电脑的主屏上的［QR link］图
标。
按照屏幕上的指示，最后触摸［关闭］按钮。
触摸［QR 码读取］，读取附带的“ 设置信息表 ”上打印的
QR 码。
安装简单设置应用程序“QR link” （免费），进行设置。
D 智能手机/平板电脑 (iOS/Android)
※在 XP，若弹出“ 新硬件搜索向导 ”窗口，点击［取消］。
屏幕上弹出“ 发现新硬件 ”的提示消息时，从微机打开“Setup”驱动器后点击
“Setup.exe”进行安装。
各部分的名称和作用
顶部 正面 背面 左侧面 右侧面
底部
WRH-150x 简易版用户手册
本项是仅在电脑初次连接本产品时所需的步骤。
使用Mac OS
步骤
English 中文
电源插孔
（microUSB）
连接符合 USB2.0（microB-A）标准的电缆。
WAN 端口
（蓝色）
用 LAN 电缆连接本产品和酒店的局域网端子。
WPS/Reset
指示灯（蓝色）
亮灯 重置功能启动
闪烁 WPS 功能工作中
熄灭 通常时
WAN 指示灯
（蓝色）
亮灯・闪烁 与 WAN 侧连接着
熄灭 未与 WAN 侧连接的状态
WLAN 指示灯
（蓝色）
亮灯・闪烁 与无线侧连接着
熄灭 未与无线侧连接的状态
WPS/Reset 按钮
按住约 1 ～ 9 秒后，WPS 功能启动
按住 10 秒以上后，重置功能启动
① WPS/Reset 指示灯 熄灭
② WAN 指示灯 蓝色亮灯或蓝色闪烁
③ WLAN 指示灯 蓝色亮灯或蓝色闪烁