Document Outline

• Important Regulatory Factors
  • Wireless Remote Control
  • Important Safety Instructions
• Table of Contents
• About the Remote Control
  • Remote Control Signals: UHF or IR
  • Installing Batteries in the Remote Control
    • 1. Press down on the slot in the battery cover (on the back of the remote control) and slide the ...
    • 2. Insert the new batteries, making sure to match the plus (“+”) ends with the plus markings on t...
    • 3. Replace the battery cover by sliding the cover back up into place.
  • Remote Control Modes
    • 1. Set up the remote to control the device. See Controlling a Device on page15 for instructions.
    • 2. Use the remote control mode buttons, SAT (satellite receiver), TV, VCR (for a VCR or a DVD pla...
• Using the Remote Control Buttons
  • SAT (Satellite Receiver) Mode
    • SAT Mode Button
    • AUX Mode Button
    • TV/Video Button
    • Menu Button
    • Power Button
    • Page Up and Page Down (Arrow) Buttons
    • Mute Button
    • Volume Button
    • Guide Button
    • Select Button
    • Up/Down/Left/Right (Arrow) Buttons
    • Recall Button
    • Information (Info) Button
    • View Button
    • Cancel Button
    • System Information (Sys Info) Button
    • Number Buttons
    • Pound Button
  • TV (Television) Mode
    • TV Mode Button
    • TV/Video Button
    • Power Button
    • Mute Button
    • Volume Button
    • Select Button
    • Up/Down (Arrow) Buttons
    • Recall Button
    • Number Buttons
  • VCR (VideoCassette Recorder) Mode
    • VCR Mode Button
    • Mute Button
    • Volume Button
    • Select Button
    • Up/Down/Left/Right (Arrow) Buttons
    • Number Buttons
  • AUX (Auxiliary) Mode for Cable TV Box
    • AUX Mode Button
    • Mute Button
    • Volume Button
    • Select Button
    • Up/Down (Arrow) Buttons
    • Recall Button
    • Number Buttons
    • Star Button
  • AUX (Auxiliary) Mode for Tuner or Amplifier
    • AUX Mode Button
    • Mute Button
    • Volume Button
    • Select Button
    • Up/Down (Arrow) Buttons
    • Star Button
• Remote Control Procedures
  • Controlling a Device
    • 1. Turn ON the device you want the remote to control, using the device’s buttons or the remote co...
    • 2. Find the brand name of the device in the tables that start on page22. If the brand is not lis...
    • 3. Press and hold the mode button for the device that you want the remote to control, for about t...
    • 4. Use the number buttons to enter the code for the device. Note: For the AUX mode, you must ente...
    • 5. Press and release the Pound (#) button. If the code is valid, the mode button backlight blinks...
    • 6. Test if the code works for the device by pressing the Power button. If the code works, the dev...
    • 7. Turn the device back ON and try some other buttons to make sure they work. Sometimes, the Powe...
    • 8. If the code you entered does not work, repeat steps 3 through 7 using another code from the ta...
    • 9. If you have tried all of the codes listed for the device without success, or if you cannot fin...
  • Changing the Remote Control Address
    • 1. Display the Important System Information menu. Note the Remote Address shown on this menu.
    • 2. Press and hold the SAT mode button about three seconds, until all the mode button backlights c...
    • 3. Use the number buttons to enter a number from 1 to 15. The SAT mode button backlight will blin...
    • 4. Press the Pound (#) button. If the address you entered is valid for the remote control, the SA...
    • 5. Press the Record button. The Remote Address on the Important System Information menu should ma...
    • 6. To check the address, press and hold the SAT mode button for three seconds. Then, press the Po...
    • 7. Press the Select button.
  • Installing an Attenuator
    • 1. Remove the UHF antenna from the UHF Remote Antenna connection on the receiver back panel.
    • 2. Attach a 10 dB attenuator to the UHF Remote Antenna connection.
    • 3. Attach the UHF antenna to the attenuator.
  • Controlling Sound Volume
    • Receiver Volume Control
      • 1. Use the TV remote control to make sure that the TV sound volume is not turned down or muted. N...
      • 2. Press the Menu button.
      • 3. Select the System Setup option.
      • 4. Select the Volume Control option. Note: If the System Setup menu does not display this option,...
      • 5. Select the TV remote volume control or the DISH remote volume control option.
      • 6. Select the Save option.
      • 7. If you are setting up the remote control for the first time, see Controlling a Device on page...
    • TV or Amplifier Volume Control
      • 1. Press and hold the AUX mode button for three seconds, then release it.
      • 2. Press the Pound (#) button.
      • 3. Press the plus (+) side of the Volume button.
      • 4. Press the 0 number button.
      • 5. Press the Pound (#) button. The AUX mode button backlight blinks three times.
      • 1. Press and hold the TV mode button for three seconds, then release it.
      • 2. Press the Pound (#) button.
      • 3. Press the plus (+) side of the Volume button.
      • 4. Press the 0 number button.
      • 5. Press the Pound (#) button. The AUX mode button backlight blinks three times.
  • Doing the Device Code Scan
    • 1. Press and hold the mode button for the device, for about three seconds. When all the other mod...
    • 2. For AUX mode only, use the number buttons to enter a number as follows: 0 is for a second TV, ...
    • 3. Press the Power button.
    • 4. Press the Up or Down arrow button to set the remote to the next code. The Down arrow button sc...
    • 5. When the remote reaches the correct code, the device turns OFF. If this happens, press the Pou...
    • 6. Press the Power button to turn the device back ON.
    • 7. Try some other remote control buttons to make sure that you have the right code.
  • Finding the Device Codes
    • 1. Press and hold the mode button for the device, for about three seconds. When all the other mod...
    • 2. Press the Pound (#) button twice. The mode light flashes the number for each digit of the curr...
• Device Codes
  • TVs
  • VCRs
  • Tuners/Amplifiers
  • Cable TV Boxes
• Trouble-Shooting Table
• Limited Warranty
  • Advance Exchange Program
• If You Need Help
  • 1. Review this Guide.
  • 2. See the Trouble-Shooting Table on page26.
  • 3. Call the DISH NetworkSM Service Center at 1-800-333-DISH (3474). Have the date of purchase and...
  • 4. A Representative will assist you. He or she will try to troubleshoot any problem you may be ha...
  • 5. If the Representative finds that you should return the remote control, he or she will give you...
  • 6. You must package returned equipment properly. Follow the instructions that the Representative ...
  • 7. Write the RA number in large, clearly visible characters on the outside of the shipping box us...
  • 8. We will: