Grizzly G0651 - Manual (Page 23)

model g0651/g0652 (mfg. since 1/10)
-21-
Extension Table
Box contents: (Figure 9) Qty
A. extension table .......................................... 1
B. lower shelf ................................................ 1
c. shelf end plate ........................................... 1
D. support legs .............................................. 2
E. lower shelf Brackets ................................. 2
Fasteners (and where used): Qty
• Cap screws m8-1.25 x 25
(rear rail/Cabinet/ext. table) .................... 8
• Flat head screws m8-1.25 x 25
(Front rail/Cabinet/ext. table) ................... 8
• Flat Washers 8mm
(Front rail/ext. table/rear rail) .............. 14
• hex nuts m8-1.25
(Front rail/ext. table/rear rail) ................ 8
• lock Washers 8mm
(Front rail/ext. table/rear rail) .............. 10
• hex Bolts m8-1.25 x 12
(Cabinet/ext. table) .................................... 2
• Flat Washers 8mm (Cabinet/ext. table) .... 2
• Flat head screws m8-1.25 x 25
(table/ext. table) ....................................... 2
• mounting plates (table/ext. table) ............ 2
• hex Bolts m6-1 x 12
(Brackets/Cabinet/legs) ............................. 2
• hex nuts m6-1
(Brackets/Cabinet) ...................................... 2
• Feet 3 ⁄
8
"-16 x 2 (legs) ................................. 2
• hex nuts 3 ⁄
8
-16 (legs) ................................ 2
• phillip head screws m6-1 x 12
(ext. table/legs/shelf Brackets) .............. 14
• Flat Washers 6mm
(ext table/legs/shelf Brackets) ............... 16
• hex Bolts w/Washers m8-1.25 x 12
(tube/ Front rail) ........................................ 9
Figure 9. extension table components.
a
B
C
d
e
if any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Outfeed Table
Box contents: (Figure 10) Qty
A. outfeed table ............................................. 1
B. lower shelf ................................................ 1
c. shelf end plate ........................................... 1
D. support legs .............................................. 2
E. lower shelf Brackets ................................. 2
Fasteners (and where used): Qty
• hex Bolts m8-1.25 x 20 w/Washer
(rear rail/outfeed table) ........................... 2
• hex nuts m8-1.25
(rear rail/outfeed table) ........................... 2
• Flat Washers 8mm
(rear rail/outfeed table) ........................... 2
• hex Bolts m6-1 x 12
(Brackets/Cabinet) ...................................... 2
• hex nuts m6-1 (Bracket/end plate) ........... 2
• Flat Washers 6mm
(outfeed table/legs/shelf Brackets) ........ 16
• phillips head screws m6-1 x 12
(outfeed table/legs/shelf Brackets) ........ 14
• Feet 3 ⁄
8
-16 x 2 (legs) .................................. 2
• hex nuts 3 ⁄
8
-16 (legs) ................................ 2
Figure 10. outfeed table components.
a
B
C
d
e
SuFFOcATION hAzARD!
Immediately discard all plas-
tic bags and packing materi-
als to eliminate choking/suf-
focation hazards for children
and animals.