MITSUBISHI ELECTRIC WD-52627 - Manual (Page 29)

Chapter 2. Connecting
29
Connecting a DVD Player with Component Video
Connecting a DVI Device
DVD Player with Component Video
Figure 9
Component video cables and audio cables are required.
These are not included with the TV.
1. Connect the Component Video cables from Y/Pr/
Pb VIDEO OUT on the back of the DVD player to
COMPONENT-2 on the TV back panel, matching the
correct connection:
• Y to Y (Green)
• Pr to Pr (Red)
• Pb to Pb (Blue)
2. Connect a set of audio cables from AUDIO OUT
on the back of the DVD player to COMPONENT-2
AUDIO Input on the TV back panel. The red cable
connects to the R (right) channel, and the white cable
connects to the L (left) channel.
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
OUTPUT
AUDIO OUTPUT RECORD OUTPUT DVI Analog Audio
1 2 VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1 2
IEEE 1394 INPUT/ OUTPUT
Net Command IR EMITTER ¸
'
,INK ¸

INPUT
PC - 60Hz VGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720
57
#BDL
1BOFM
4FDUJPO
7*%&0
4
:
$#
$3
7*%&0
065
#*5453&".1$. 
$)
463306/% $)
-
3
$&/5&3
46#800'&3 463306/% '30/5 $0"9*"- 015*$"-
"6%*0
065 "$
*/ .*546#*4)*
%7%
1-":&3 .0%&- %%
108&3
4611-:












7_
)[ 108&3
$0/46.15*0/












8
.*546#*4)*
%*(*5"-
&-&$530/*$4 %*453*#65&%
#:

+&30/*.0
30"% *37*/&

$"

."%&
*/
+"1"/
".&3*$"

*/$
4&3*"-
/0 ."/6'"$563&%




%7%
#BDL
1BOFM
3FE
8IJUF
8IJUF
3FE
Figure 9. Connecting a DVD Player with Component
Video
Note: NetCommand® assumes you connected your
DVD player to Component-2. If you add a second
DVD or use any other inputs for your DVD, this change
must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
IMPORTANT
See Appendix B for component video signal
compatibility information.
For digital audio connections to your A/V
receiver , see your DVD player and A/V
receiver Owner’s Guides.
DVI Device
Figure 10
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable
and audio cables are required. These are not included with the
TV. They may be available at your local electronics retailer.
1. Connect the DVI-to-HDMI cable (recommended) or
HDMI cable with DVI/HDMI adaptor from the DVI
device’s back panel to the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI device
for best performance.
2. Connect a set of audio cables from AUDIO OUT
on the DVI device back panel to the INPUT/DVI
Analog Audio on the TV back panel. The red cable
connects to the R (right) channel, and the white
cable connects to the L (left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require
connecting to an analog input first, in order to view
on-screen menus and select DVI as the ouput.
Please review your equipment instructions for DVI
connectivity and compatibility.
!.4
#!",%
3!4%,,)4%
46
!5$)/ 2
,
$6)
%7*
%FWJDF
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
OUTPUT
AUDIO OUTPUT RECORD OUTPUT
DVI Analog Audio
1 2 VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1 2
IEEE 1394 INPUT/ OUTPUT
Net Command IR EMITTER ¸
'
,INK ¸

INPUT
PC - 60Hz VGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720
%7*UP)%.*
$BCMF




57
#BDL

1BOFM
%FUBJM
Figure 10. Connecting a DVI Device
CAUTION: To ensure continued FCC
compliance, the user must use a
shielded video interface or HDMI cable
with bonded ferrite cores at both ends
when using the PC input.