MITSUBISHI ELECTRIC WD-52627 - Manual (Page 26)

26
Chapter 2. Connecting
Connecting a VCR to an Antenna or Wall Outlet Cable
Connecting VCR Audio and Video to the TV
VCR to an Antenna or Wall Outlet
Cable (Audio & Video)
Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV.
1. Connect the incoming cable or Antenna to IN on the
RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the VCR back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® feature.
4. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT-1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white
cable connects to the L (left) channel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.
Note:
NetCommand®
will assume your
VCR is connected
to inputs as shown
on this page. If
you use any other
inputs for your VCR
or add a second
VCR, this change
must match in
the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.
Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable
5. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT-1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.
6. For NetCommand® controlled recordings
(including TV Guide On Screen), connect a set
of audio cables from AUDIO IN on the VCR back
panel to RECORD OUTPUT/AUDIO-LEFT and
AUDIO-RIGHT on the TV back panel. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
7. Complete the NetCommand controlled recordings
connections by connecting a Video cable from
VIDEO IN on the VCR back panel to RECORD
OUTPUT/VIDEO on the TV back panel.
COMPONENT YPbPr (480i/480p/720p/1080i) INPUT
1 2
S-VIDEO
VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
DTV/CABLE/ VHF/UHF
ANT 1 / MAIN ANT 2 / AUX
DIGITAL AUDIO OUTPUT CableCARD™ USE WITH ANT 1 CARD TOP
1 2
Y
Pb
Pr
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
OUTPUT
AUDIO OUTPUT RECORD OUTPUT DVI Analog Audio
1 2 VIDEO
AUDIO- LEFT/ (MONO)
AUDIO- RIGHT
MONITORLINK™/HDMI VIDEO 480i/480p/720p/1080i AUDIO PCM LINEAR
1 2
IEEE 1394 INPUT/ OUTPUT
Net Command
IR EMITTER ¸
'
,INK ¸

INPUT
PC - 60Hz VGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720
)46

*/
065
065
580
8
" :
41-*55&3


*ODPNJOH

$BCMF
3'
4QMJUUFS

7$3
CBDL
QBOFM







 
*G
ZPVS
7$3
IBT
B

WJEFP
DIBOOFM
PS
3'

0/0''
TXJUDI

TFU
JU

UP
0''
"UUBDI
POMZ
POF
DBCMF
UZQF


4WJEFP
SFDPNNFOEFE
JG

BWBJMBCMF
46