JVC SR-DVM700ER - Manual (Page 50)

Filename [DVM700ER_11Editing.fm]
Masterpage:Left+
50
EN
EDITING
Page 50 Wednesday, 20 September 2006 10:03
You can use a camcorder as the source player and your unit as the
recording deck. If your camcorder has a DV IN/OUT connector, you
can use the camcorder as the recording deck and your unit as the
source player.
1
Make connections.
A If the camcorder has no S-VIDEO output connector:
^ connect the camcorder’s AUDIO/VIDEO OUTPUT
connectors to the unit’s [VIDEO/AUDIO ((MONO) L/R)] input
connectors on the front panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
C If the camcorder has a DV IN/OUT connector:
^ connect the camcorder’s DV IN/OUT connector to the unit’s
[DV IN/OUT] connector.
● When using your unit as the source player, refer to the
camcorder’s instruction manual for the recording procedure.
2
Press DV/HDD/DVD on the unit repeatedly to select the
recording deck.
3
Press INPUT SELECT +/– on the remote control or
INPUT SELECT on the unit to select
AF-1B or ADVB.
● Set AF-1 INPUTB to AVIDEOB for the [VIDEO] input connector,
or AS-VIDEOB for the [S-VIDEO] input connector, depending on
the connector being used. ( A pg. 59)
4
Press REC MODE repeatedly to set the recording mode. For
DV deck, press REC MODE on the remote control to set the
recording mode.
5
Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6
Press R on the unit to start recording. Or while holding R, press
I on the remote control. The dubbing starts.
7
Press o on the unit, then stop playback on the camcorder.
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating
procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
● When you are editing through the [DV IN/OUT] connector, the
unit will stop if the player begins playing a blank portion of tape or
the signal is interrupted.
● When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV 204U).
● To edit through the [DV IN/OUT] connector using the HDD or
DVD deck, refer to
ADV Dubbing (HDD & DVD Deck Only)B
( A pg. 48).
● When using your unit as the recording deck, chapters (marks)
can be automatically created. Set
ADV AUTO CHAPTERINGB to
AONB. (A pg. 58)
Edit From A Camcorder
A If the camcorder has no S-VIDEO output connector:
Recorder
Player
To [VIDEO/AUDIO
((MONO) L/R)] input
Audio/video cable
(not supplied)
AUDIO/VIDEO OUTPUT
B If the camcorder has an S-VIDEO output connector:
To
[S-VIDEO]
input
To [AUDIO] input
S-video cable
(not supplied)
AUDIO OUTPUT
Audio cable
(not
supplied)
S-VIDEO
OUTPUT
Recorder
Player
C If the camcorder has a DV IN/OUT connector:
To [DV IN]
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
Player/Recorder
Recorder/Player
● Slide the TV/DVD switch to DVD.
DVM700ER_00.book Page 50 Wednesday, September 20, 2006 10:03 AM