JVC XV-NA7SL - Manual (Page 11)

Getting started
Getting started
9
XV-NA7SL/LET0212-004A/English
To switch the signal format from the remote control unit
If you set the NTSC/REMOTE/PAL switch on the rear panel to "REMOTE," you can select the component signal format
from the remote control unit.
• Before this operation, set the NTSC/REMOTE/PAL switch on the rear panel to "REMOTE," while the unit is turned off.
Press and hold down the PAL/NTSC button
The signal format switches between the PAL and NTSC.
To check the current signal format, press PAL/NTSC button while the unit is turned on. The display window on the front
panel shows the current status ([NTSC] or [PAL]).
To make the Progressive scanning mode selection active
The unit supports the Progressive scanning system as well as the conventional Interlaced scanning system. If your
television or monitor supports the progressive video input, you can enjoy a high quality picture by making the
Progressive scanning mode active.
The Progressive scanning mode selection only works when NTSC/REMOTE/PAL switch on the rear panel is set to "NTSC"
or "REMOTE." However, note that, when the NTSC/REMOTE/PAL switch on the rear panel is set to "REMOTE" and set
NTSC system from the remote control unit first.
• When the unit turned on, and the NTSC/REMOTE/PAL switch on the rear panel is set to "NTSC" or "REMOTE."
NOTES
• When switching the signal format from the remote control, make sure that the disc is stopped.
• You must change the switch position on the rear panel while unit power is off. Otherwise, the changed setting is not effective.
• If you set the NTSC/REMOTE/PAL switch on the rear panel is set to "REMOTE" or "NTSC," the unit output the signals from the
COMPONENT VIDEO OUT jacks only.
• When you set the NTSC/REMOTE/PAL switch on the rear panel is set to "REMOTE," the VIDEO SIGNAL SELECTOR on the rear
panel is not effective.
About SCANNING MODE
To display video on the television (monitor) screen, the conventional scanning method is called "Interlaced scanning."
With this method, only half of the horizontal lines are displayed at a time. So two fields complete a single picture
(frame); i,e., the first field, containing all the odd-numbered lines, is displayed followed by the second field, containing
all the even-numbered lines.
On the other hand, the Progressive scanning is resulting in flicker-free, high-density picture.
Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video
source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24-
frame-per-second information, while (NTSC) video sources are recorded as 30-frame-per-second (60-field-per-secon
interlaced) information.
When the unit plays back a film source material, uninterlaced progressive output signals are created using the original
information. When a video source material is played back, the unit interleaves lines between the interlaced lines on
each to create the interpolated picture and outputs as the progressive signal.
TV2
2
TV1
1
TV3
3
TV5
5
TV4
4
TV6
6
TV8
8
TV7
7
TV9
9
TV0
0
TV-/--
10
MUTING
+10
TV/VIDEO CANCEL TITLE/ GROUP RETURN
VFP AUDIO SUB TITLE REPEAT
ANGLE DIGEST
3D PHONIC PAL/ NTSC
ZOOM
AMP VOL
PROGRESSIVE SCAN fs/Rate
RM-SXV012E
REMOTE CONTROL
OPEN/
CLOSE
TV DVD
NEXT PREVIOUS
SELECT STROBE CLEAR
SLOW- SLOW+
VOL- VOL+
CH +
CH -
TO P ME NU ME NU
ON SC RE EN CH OIC E
ENTER
STANDBY/ON
TV DVD
PAGE
PAL/NTSC
XV-NA7SL(B).book Page 9 Wednesday, July 31, 2002 1:00 PM