JVC XV-NA7SL - Manual (Page 16)

Getting started
Getting started
14
XV-NA7SL/LET0212-004A/English
You can operate your TV from the remote control unit.
Setting the remote control signal for
operating your TV
1 Set the TV - DVD switch to "TV."
2 Hold down TV/VIDEO - CANCEL until step 4 is
finished.
3 Enter the manufacturer code of your TV listed below
by using the numeric buttons (0 to 9).
Example:
To enter the manufacturer code "01": Press "0" then
"1."
Hint
• When you purchased the unit, the manufacturer code is set
to "JVC" (01).
4 Press ENTER.
Manufacturer code list
5 Release TV/VIDEO - CANCEL.
6 Try to operate the TV by pressing
TV STANDBY/ON
.
If your TV turns on or off, you have successfully set
the control signal.
The following buttons can be used for operating the
TV.
To use
5/∞ (CH+, CH–), 2/3(VOL–, VOL+), TV/VIDEO -
CANCEL and numeric buttons for TV control, set the
TV - DVD switch to "TV."
You can control the volume of a JVC’s amplifier or
receiver by using the AMP VOL +/– buttons on the
remote control unit.
Pressing the + button raises the audio volume of the
amplifier or receiver, while pressing the – button lowers
the volume.
To use the remote control unit for TV
operation
Manufacturer No. Manufacturer No.
AIWA 36 MIVAR 29
BEIJING 22 NEC 20
CCE 02 NOBLEX 22
CHANGHONG 34 NOKIA 31
DAEWOO 17, 37 PANASONIC 04, 11
FERGUSON 27 PEONY 34, 38, 39
FINLUX 30 PHILCO 10, 17, 21
FUNAI 32 PHILIPS 02
GRADIENTE 15, 20 RCA 05
GRUNDIG 19 SAMSUNG 12, 33,
34, 35
HITACHI 10
ITT 28 SANYO 13, 16
JINXING 38 SEARS 13
JVC 01, 23,
24, 25 SHARP 06
SONY 07
KONKA 40 TCL 41
LG (GOLDSTAR) 18 THOMSON 26
MAGNAVOX 02 TOSHIBA 08,14
MITSUBISHI 03 ZENITH 09
TV2
2
TV1
1
TV3
3
TV5
5
TV4
4
TV6
6
TV8
8
TV7
7
TV9
9
TV0
0
TV-/--
10
MUTING
+10
TV/VIDEO CANCEL TITLE/ GROUP RETURN
VFP AUDIO SUB TITLE REPEAT
ANGLE DIGEST
3D PHONIC PAL/ NTSC
ZOOM
AMP VOL
PROGRESSIVE SCAN fs/Rate
OPEN/
CLOSE
TV DVD
NEXT PREVIOUS
SELECT STROBE CLEAR
SLOW- SLOW+
VOL- VOL+
CH +
CH -
TO P ME NU ME NU
ON SC RE EN CH OIC E
ENTER
STANDBY/ON
TV DVD
PAGE TV/VIDEO -
CANCEL
ENTER
TV - DVD
switch
Numeric
buttons
TV STANDBY/
ON
Turns the TV on or off.
Switches the TV input mode between
TV and VIDEO.
Selects the TV channels directly.
* For some TVs, pressing "+10"
functions as the "100+," while "10"
functions as the ENTER button if
your TV requires pressing the
ENTER button after selecting a
channel number.
Mutes the TV sound.
Changes the TV channels.
Adjusts the TV volume.
NOTE
• If there is more than one code listed for the
manufacturer of your TV, try them one by one until you
succeed.
To control the volume of a JVC’s
amplifier or receiver
TV DVD
TV
TV/VIDEO
CANCEL
~ TV1
1
TV-/--
10
TV0
0
MUTING
+10
CH
+
CH
-
VOL- VOL+
AMP VOL
XV-NA7SL(B).book Page 14 Wednesday, July 31, 2002 1:00 PM