Siemens Stober CombiDrive CM400/3 - Manual (Page 3)

© STÖBER plc 1998
05.02.01
Safety Precautions
Before installing and putting this equipment into operation, please read these safety precautions and
warnings carefully and all the warning signs attached to the equipment. Make sure that the warning signs
are kept in a legible condition and replace missing or damaged signs.
WARNING
This equipment contains hazardous voltages and
controls hazardous rotating mechanical parts. Loss
of life, severe personal injury or property damage
can result if the instructions contained in this
manual are not followed.
Only suitable qualified personnel should work on
this equipment, and only after becoming familiar
with all safety notices, installation, operation and
maintenance procedures contained in this manual.
The successful and safe operation of this
equipment is dependent upon its proper handling,
installation, operation and maintenance.
•
The CombiDrive ® operates at high voltages.
•
ALWAYS isolate the equipment from the power
supply before starting any work on it.
•
The dc-link capacitor remains charged to
dangerous voltages even when the power is
removed. For this reason it is not permissible
to open the equipment until one minute after
the power has been turned off. When handling
the open equipment it should be noted that live
parts are exposed. Do not touch these live
parts.
•
The equipment must not be connected to a
supply via an ELCB (Earth Leakage Circuit
Breaker
- see DIN VDE 0160, section 6.5).
•
The following terminals can carry dangerous
voltages even if the inverter is inoperative:
-the power supply terminals L1, L2, L3.
- the motor terminals U, V, W.
• Ensure that the inverter’s cover has been fitted
correctly before applying mains power to the
CombiDrive
® . If a Braking Unit has been
supplied, ensure that the terminal connections
fitted to the underside of the cover mate
correctly with those on the inverter when
refitting the cover.
• Only qualified personnel may connect, start the
system up and repair faults. These personnel
must be thoroughly acquainted with all the
warnings and operating procedures contained
in this manual.
•
Certain parameter settings may cause the
motor to restart automatically after an input
power failure.
• This equipment must not be used as an
‘emergency stop’ mechanism (see EN 60204,
9.2.5.4).
CAUTION
•
Children and the general public must be
prevented from accessing or approaching the
equipment!
• This equipment may only be used for the
purpose specified by the manufacturer.
Unauthorised modifications and the use of
spare parts and accessories that are not sold
or recommended by the manufacturer of the
equipment can cause fires, electric shocks
and injuries.
• Keep these operating instructions within easy
reach and give them to all users!
European Low Voltage & EMC Directives
The CombiDrive ® product complies with the requirements of the Low
Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC.
The units are certified for compliance with the following standards:
EN 60204-1 Safety of machinery - Electrical equipment of
machines
EN 60146-1-1 Semiconductor converters - General
requirements and line commutated converters
BS EN50081-2: 1995 Generic Emission Standard - Industrial
Environment
BS EN50082-2: 1995 Generic Immunity Standard - Industrial
Environment
Proviso: The CombiDrive ® does not meet CE requirements when
an OPm2 is connected.
European Machinery Directive
The CombiDrive ® product (combined inverter and motor assembly) is
suitable for incorporation into machinery.
The CombiDrive ® must not be put into service until the machinery into
which it is incorporated has been certified to be in compliance with the
provisions of the European Directive 89/392/EEC.
Note: Only valid for machinery to be operated in the European
Community.
European EMC Directive
When installed according to the recommendations described in this
manual, the CombiDrive
® fulfills all requirements of the EMC directive as
defined by the EMC Product Standard for Power Drive Systems
EN61800-3.