Specifications, Appendix – Sharp DT-500 User Manual
Page 62
Appendix
61
Specifications
Projector
DT-500
NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Single Chip Digital Micromirror Device
TM
(DMD
TM
) by Texas Instruments
Panel size: 0.65", 1chip DMD
Drive method: Digital Light Processing (DLP™)
No. of dots: 983,040 dots (1280 [H]
× 768 [V])
1–1.15
× zoom lens, F2.4–2.6, f = 19.0–21.9 mm
275 W DC lamp
RCA connector
Y: 1.0 Vp-p, sync negative, 75
Ω terminated
P
B
(C
B
): 0.7 Vp-p, 75
Ω terminated
P
R
(C
R
): 0.7 Vp-p, 75
Ω terminated
4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75
Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75
Ω terminated
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75
Ω
terminated
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75
Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
HDMI terminal (video signal only)
720 TV lines (DTV720P)
45–85 Hz
15–70 kHz
12–85 MHz
AC 100–240 V
3.7 A
50/60 Hz
355 W (Lamp Setting “Bright”)/
310 W (Lamp Setting “Eco + Quiet”) with AC 100 V
340 W (Lamp Setting “Bright”)/
300 W (Lamp Setting “Eco + Quiet”) with AC 240 V
4 W (AC 100 V) – 5 W (AC 240 V)*
1
1,335 BTU/hour (Lamp Setting “Bright”)/
1,165 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 100 V
1,280 BTU/hour (Lamp Setting “Bright”)/
1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V
41°F to 95°F (+5°C to +35°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
12
13
/
32
"
Ч 4
19
/
64
"
Ч 11
1
/
32
"
(315 (W)
× 109 (H) × 280 (D) mm) (main body only)
12
13
/
32
"
Ч 4
47
/
64
"
Ч 11
37
/
64
"
(315 (W)
× 120 (H) × 294 (D) mm) (including adjust-
ment foot and projecting parts)
8.8 lbs. (4.0 kg)
Remote control, Power cord for U.S. and Canada, etc., Operation manual
Product type
Model
Video system
Display method
DMD panel
Lens
Projection lamp
Component input signal
(INPUT1/2)
S-video input signal
(INPUT 3)
Video input signal
(INPUT 4)
Computer RGB/
Component input signal
(INPUT 5)
HDMI input signal
(INPUT 6)
Horizontal resolution
Vertical frequency
Horizontal frequency
Pixel clock
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Replacement parts
*
1
When STANDBY Mode is set to “Eco”
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specifica-
tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
DT-500_EN_m
06.2.16, 10:04 AM
61