Kenwood TS-870S - Manual (Page 90)

84
● APPENDICES
PARAMETER DESCRIPTION
Parameters are used to specify information necessary
to implement the desired command. The parameters
to be used for each command are predetermined. The
number of digits assigned to each parameter is also
predetermined. If a particular parameter is not
applicable to the TS-870S, the parameter digits should
be filled using any character except the ASCII control
codes (00 to 1Fh) and the terminator (;).
BAD COMMAND EXAMPLES:
IS1000; Not enough parameters specified
(No direction given for the IF shift)
IS+100; Not enough digits
(Only three frequency digits given)
IS_+_1000; Unnecessary characters between
parameters
IS+10000; Too many digits
(Five frequency digits given)
PARAMETER TABLE
For-
mat
No.
Name Format
No. of
Digits
METER VALUE
METER
SWITCH
PLAYBACK
CHANNEL
ANTENNA
TUNER
GAIN
AI NUMBER
ANTENNA
NUMBER
CW BREAK-IN
MENU NUMBER
MENU
SELECTION
RECEIVE
FILTER
DISPLAY
FILTER WIDTH
AGC TIME
CONSTANT
IF SHIFT
DIRECTION
IF SHIFT
FREQUENCY
4
1
1
1
3
1
1
1
3
4
8
4
3
1
4
22
24
27
30
31
32
33
34
35
36
37
38
39
40
41
Represented using
0000 (min.)~
0030 (max.). Relative
values are output.
0: No selection
1: SWR
2: COMP
3: ALC
0: Not playing back. A
Set command
cancels playback.
1: Channel 1
2: Channel 2
3: Channel 3
4: Channel 4
0: Antenna tuner thru
1: Antenna tuner in-line
Represented using
000 (min.)~255 (max.).
0: AI OFF
1: IF command outputs
its Answer command
periodically.
2: For parameter
changes, the
corresponding
Answer command is
output.
3: Both 1 and 2.
1: ANT 1
2: ANT 2
1: Semi break-in ON
2: Full break-in ON
Represented using
000~068.
See table on page 87.
Represented using
00000000~FFFFFFFDh.
Represented in units of
10 Hz using 0000~9999.
Represented using
000 (min.)~255 (max.).
000~005: OFF
"+": Upward freq. shift
(or "_")
"–": Not used (error
occurs).
Represented in Hz using
0000~9999.
For-
mat
No.
Name Format
No. of
Digits
SW
MODE
FUNCTION
FREQUENCY
RIT/XIT
FREQUENCY
MEMORY
CHANNEL
MEMORY
CHANNEL
SPLIT DATA
MEMORY
LOCKOUT
TX/RX
TONE NUMBER
MODEL
NUMBER
1
1
1
11
5
2
1
1
1
2
3
1
2
3
4
5
7
9
10
11
14
16
0: OFF 1: ON
0: VFO A
1: VFO B
2: MEMORY
Represented in Hz.
Ex.: 00014230000 is
14.230 MHz
The first digit is "+" or "–",
and the remaining four
digits indicate the
frequency in Hz.
Ex.: +5320 is +5.32 kHz
"_" can be used for
"+".
Represented using
00~99.
0: Receive
1: Transmit
0: Not locked out
1: Locked out
0: Receive
1: Transmit
Represents the Tone
number (01~39). See
the Subtone Table on
page 85.
Represents the type of
transceiver. The
TS-870S number is 015.
Note: Applicable to
Single Beep and
Morse abbreviation
modes.
5: AM
6: FSK
7: CW-R
8:
No Mode
9: FSK-R
0: No mode
1: LSB
2: USB
3: CW
4: FM