Reading command tables, Command tables, 89 appendices – Kenwood TS-870S User Manual
Page 95
89
APPENDICES
●
READING COMMAND TABLES
q Command
w Name
e Function of the command
r The format of the command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set
command.
t The format of the command for reading the transceiver’s current status is shown. When oblique lines are drawn in
the 1st and 2nd columns, there is no Read command.
y The format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd
columns, there is no Answer command.
u The number of command digits is shown.
i Corresponds to the parameter of the command format.
o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter
Table {page 84}.
!0 Indicates the function of the parameter.
COMMAND TABLES
Note:
Parameters that have a Parameter Function of “NOT USED” are not supported by the TS-870S. Any character except the ASCII control
codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.
1
Auto information OFF/ON
AI
AUTO INFORMATION
2
Parameter Format
Parameter function
P1
32
AI NUMBER
3
4
5
6
7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6
7
8
9 10 11 12 13 14
1
2
3
A
I
P1
A
I P1
;
A
I
;
4
5
6
7
8
9 10 11 12 13 14
;
Note:
For other commands, controls whether
changing a parameter will or will not trigger
the corresponding Answer command
to be output.
Ex:
For IF, the Answer command is output
if the step frequency or RIT/XIT
frequency is changed.
1
Sets or reads AF gain.
AG
AF GAIN
2
Parameter Format
Parameter function
P1
31
AF GAIN
3
4
5
6
7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6
7
8
9 10 11 12 13 14
1
2
3
A
G
P1
;
A
G
;
4
5
6
7
8
9 10 11 12 13 14
P1
A G
;
1
Selects antenna connector ANT 1/ ANT 2.
AN
ANTENNA NUMBER
2
Parameter Format
Parameter function
P1
33
ANTENNA
NUMBER
3
4
5
6
7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6
7
8
9 10 11 12 13 14
1
2
3
A
N P1
A
N P1
;
A
N
;
4
5
6
7
8
9 10 11 12 13 14
;
1
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
AC
ANTENNA TUNER CONTROL
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
does not start tuning).
P1: RX THRU/IN P2: TX THRU/IN
2
Parameter Format
Parameter function
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
3
4
5
6
7
8
9 10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6
7
8
9 10 11 12 13 14
1
2
3
A
C
P2 P3 ;
A
C P1 P2 P3 ;
A
C
;
4
5
6
7
8
9 10 11 12 13 14
1
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
AC
ANTENNA TUNER CONTROL
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
does not start tuning).
P1: RX THRU/IN P2: TX THRU/IN
2
Parameter Format
Parameter function
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
3
4
5
6
7
8
9
10 11 12 13 14
Input
Function
Output
Set
Read
Answer
1
2
3
4
5
6
7
8
9
10 11 12 13 14
1
2
3
A
C
P2 P3
;
A
C
P1 P2 P3
;
A
C
;
4
5
6
7
8
9
10 11 12 13 14
q
u
i
o
!0
w
r
t
y
e