Linear AE-100 - Manual (Page 21)

21
PPN 30
30#SUB-UNITS#5#
SUB-UNITS = EACH SUB-UNIT NUMBER (2-4) TO COPY
ACCESS DATA TO IN A MULTI-UNIT INSTALLATION
COPY ACCESS DATA ONLY FROM MASTER TO SUB-UNITS
PPN 34
34#SUB-UNITS#5#
SUB-UNITS = EACH SUB-UNIT NUMBER (2-4) TO COPY
ALL DATA TO IN A MULTI-UNIT INSTALLATION
COPY ALL DATA FROM MASTER TO SUB-UNITS
PPN 35
35#MESSAGE#CLEAR#
MESSAGE = ERROR MESSAGE DISPLAYED
CLEAR = 5 TO CLEAR ERROR LOG
CLEAR = # TO EXIT WITHOUT CLEARING ERROR LOG
DISPLAY/CLEAR SYSTEM ERRORS
STANDARD PROGRAMMING METHOD
NOTE:
TO ALLOW FOR MULTI-UNIT NETWORK COMMUNICATIONS,
WHEN EXECUTING THIS COMMAND REMOTELY OVER THE
TELEPHONE, THE SYSTEM WILL DISCONNECT YOUR CALL
AFTER STEP #3 THEN COPY THE DATA FROM THE MASTER
UNIT TO THE SUB-UNITS.
NOTE:
TO ALLOW FOR MULTI-UNIT NETWORK COMMUNICATIONS,
WHEN EXECUTING THIS COMMAND REMOTELY OVER THE
TELEPHONE, THE SYSTEM WILL DISCONNECT YOUR CALL
AFTER STEP #3 THEN COPY THE DATA FROM THE MASTER
UNIT TO THE SUB-UNITS.
System Utility Commands
Several utility commands are available for the system. Utility commands
can be used to copy data to other units in a multi-unit installation, clear
memory, display system information, and control the relays.
For each of the following steps, enter the Master Password and enter
Programming Mode (if the unit is not already in that mode). Exit
Programming Mode when all programming is complete.
Copy Access Data Only from Master to Sub-units
To synchronize programming in multi-unit installations, the Directory
Entries and Stand-alone Entry Codes can be copied from the master unit
to selected sub-units.
✦ NOTE: PPN numbers 71 and 7 must be programmed before this command
will operate.
✦ NOTE: This utility command can only be performed from the “master” unit.
CAUTION: This utility command will overwrite ALL the access data in the
selected sub-units.
1. Press
2. Enter the unit number(s) of all of the sub-units to receive the access data.
Examples:
To copy to unit two only enter •
To copy to unit three only enter •
To copy to units two & three enter •
To copy to units two, three, and four enter •
3. To execute the command, enter or enter to exit (any other
entry will abort the command).
Copy All Data from Master to Sub-units
To synchronize programming in multi-unit installations, all system data
can be copied from the master unit to selected sub-units. This data
includes the Directory Entries, Stand-alone Entry Code data, and all
system option settings (except the sub-unit number and password).
✦ NOTE: PPN numbers 71 and 7 must be programmed before this command
will operate.
✦ NOTE: This utility command can only be performed from the “master” unit.
CAUTION: This utility command will overwrite ALL the data in the selected
sub-units.
1. Press
2. Enter the unit number(s) of all of the sub-units to receive the full data set.
Examples:
To copy to unit two only enter •
To copy to unit three only enter •
To copy to units two & three enter •
To copy to units two, three, and four enter •
3. To execute the command, enter or enter to exit (any other
entry will abort the command).
Display/Clear System Errors
The system’s power indicator will fl ash if any system errors occur. These
errors include loss of AC power and low backup battery. In multi-unit
installations, the master unit logs communication errors with sub-units.
✦ NOTE: This step cannot be performed remotely through the telephone.
1. Press
2. The display will show any errors pending.
3. Press to display the next error message (if any).
4. When there are no more error messages to be displayed, the system will
display “Clear Error Log?”.
5. Enter
to clear the error log - or - enter to exit.