Lincoln Electric PIPELINER 11498 - Manual (Page 17)

D-1 MAINTENANCE D-1
SAFETY PRECAUTIONS
GENERAL INSTRUCTIONS
1. Blow out the welder and controls with an air hose at
least once every two months. In particularly dirty
locations, this cleaning may be necessary once a
week. Use low pressure air to avoid driving dirt into
the insulation.
2. “Current Range Selector” contacts should not be
greased. To keep the contacts clean, rotate the cur-
rent control through its entire range frequently.
Good practice is to turn the handle from maximum
to minimum setting twice each morning before start-
ing to weld.
3. Put a drop of oil on the “Current Range Selector”
shaft at least once every month.
4. When necessary, remove the sediment bowl, if so
equipped, from beneath the fuel tank and clean
out any accumulated dirt and water.
5. Follow the engine service schedule in this manual
and the detailed maintenance and troubleshooting in
the engine manufacturer’s manual.
COOLING SYSTEM
The PIPELINER® 200D KUBOTA is equipped with a
pressure radiator. Keep the radiator cap tight to pre-
vent loss of coolant. Clean and flush the cooling sys-
tem periodically to prevent clogging the passage and
overheating the engine. When antifreeze is needed,
always use the permanent type.
BEARINGS
This welder is equipped with a double-shielded ball
bearing having sufficient grease to last indefinitely
under normal service. Where the welder is used con-
stantly or in excessively dirty locations, it may be nec-
essary to add one half ounce of grease per year. A
pad of grease one inch wide, one inch long, and one
inch high weighs approximately one half ounce. Over-
greasing is far worse than insufficient greasing.
When greasing the bearings, keep all dirt out of the
area. Wipe the fittings completely clean and use clean
equipment. More bearing failures are caused by dirt
introduced during greasing than from insufficient
grease.
COMMUTATOR AND BRUSHES
Uncovered rotating equipment can be dangerous.
Use care so your hands, hair, clothing or tools do
not catch in the rotating parts. Protect yourself
from particles that may be thrown out by the rotat-
ing armature when stoning the commutator.
------------------------------------------------------------------------
Shifting of the commutator brushes may result in:
- Change in machine output
- Commutator damage
- Excessive brush wear
Periodically inspect the commutator, slip rings, and
brushes by removing the covers. DO NOT remove or
replace these covers while the machine is running.
Commutators and slip rings require little attention.
However, if they are black or appear uneven, have
them cleaned by an experienced maintenance man
using fine sandpaper or a commutator stone. Never
use emery cloth or paper for this purpose.
PIPELINER® 200D KUBOTA
Have qualified personnel do the maintenance
work. Turn the engine off before working inside
the machine. In some cases, it may be neces-
s a r y t o r e m o v e s a f e t y g u a r d s t o p e r f o r m
required maintenance. Remove guards only
when necessary and replace them when the
maintenance requiring their removal is com-
plete. Always use the greatest care when work-
ing near moving parts.
Do not put your hands near the engine cooling
blower fan. If a problem cannot be corrected by
following the instructions, take the machine to
the nearest Lincoln Field Service Shop.
-----------------------------------------------------------------------
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• I n s u l a t e y o u r s e l f f r o m w o r k a n d
ground
• Always wear dry insulating gloves.
------------------------------------------------------------------------
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or
vent exhaust outside.
------------------------------------------------------------------------
MOVING PARTS can injure.
• Do not operate with doors open or
guards off.
• Stop engine before servicing.
• Keep away from moving parts.
------------------------------------------------------------------------
See additional warning information at
front of this operator’s manual.
-----------------------------------------------------------
WARNING
WARNING