Panasonic AG-TL950 - Manual (Page 43)

43
*
1
2
3
*
1
2
3
4
5
6
7
*
.
.
.
*
.
.
.
.
.
.
.
*
S
E
C
[
R
R
D
T
A
R
R
*
R
X
N
A
E
E
U
A
U
E
E
*
I
T
T
L
C
C
R
P
T
P
P
[
/
*
*
A
*
*
A
E
O
E
E
S
E
R
T
R
M
T
T
*
*
A
A
R
X
E
A
M
O
-
I
E
R
T
E
I
T
C
P
/
D
M
O
N
E
*
*
/
*
*
E
S
E
O
N
D
W
P
R
E
R
E
S
E
*
D
*
*
*
L
E
X
E
N
E
N
*
E
*
M
*
A
C
T
C
D
N
S
*
*
*
O
*
Y
*
*
*
*
D
O
*
*
*
D
*
*
*
M
*
*
*
R
*
*
*
E
*
*
*
O
*
*
*
*
*
*
*
*
*
*
*
D
*
*
*
M
*
*
*
*
*
*
*
E
*
*
*
O
*
*
*
*
*
*
*
]
*
N
*
D
S
*
1
*
*
*
*
*
O
*
E
E
*
8
*
*
*
*
*
*
R
*
]
N
*
0
*
*
*
*
*
O
M
O
*
S
O
S
O
O
O
O
*
F
A
F
*
O
F
E
F
F
F
F
*
F
L
F
*
R
F
C
F
F
F
F
6-7 Repeat Recording
When the tape comes to the end during recording, it is automatically rewound and recording starts again from the beginning.
6 RECORDING
5 To execute repeat recording, set <REPEAT REC> in
<VTR MODE> to “ON”.
• The “REPEAT” indication in the VCR’s display lights.
5 Setting the <TAPE END MODE> menu switch in
<ALARM/SENSOR MODE>
• If this menu switch is set to “STOP”, the Stop mode is
forcibly engaged when the tape ends even if there is
an alarm or sensor recording.
To continue repeat recording even if an alarm
recording or sensor recording takes place during
recording, set <TAPE END MODE> to “OFF”.
When the Tape End Forced Stop mode and Repeat
Rec mode are engaged and an alarm or sensor
recording takes place, the “REPEAT” indication goes
out.
5 Automatic recording check function
This unit is provided with an automatic recording
check function which automatically determines
whether or not recording is satisfactory at the tape
beginning in repeat recording.
• To activate the automatic recording check
function, set the <AUTO REC CHECK> menu
switch in <VTR MODE> to “ON”.
5 Operation of the automatic recording check
function
• Recording is performed from the beginning of the
tape for several seconds during repeat recording.
Then the recorded section is automatically played
back to check whether or not the signals have
been recorded properly. If the recording is
satisfactory, recording resumes.
• If the recording is unsatisfactory, the heads are
cleaned automatically. Recording is restarted for
several seconds and then the recording is
checked again. If the recording is still
unsatisfactory, the error code “E-09” is shown on
the display and recording resumes.
Tape beginning position
Auto recording for
several seconds
Repeat recording
Recording check Recording
Normal
Auto head
cleaning
Recording
Recording check
The error code “E-09”
remains on the display.
Auto head
cleaning
Auto recording for
several seconds
Display
Recording
Normal
Defect
Defect
VIDEO/VTR MODE screen
ALARM/SENSOR MODE screen
5 When the <AUTO REC CHECK> menu switch is set
to “ON”
* When repeat recording is executed, any previously
executed alarm recordings will be erased.
Note:
• Continuous repeat recording over long periods
may produce excessive wear and tear on the
tape and VCR. Be sure to replace the tape
periodically (refer to page 28).
Set to “OFF”
*
1
2
3
*
1
2
3
4
5
6
7
*
.
.
.
*
.
.
.
.
.
.
.
*
I
D
Q
*
H
M
E
A
A
R
R
*
N
E
U
*
I
E
X
U
U
E
E
*
T
A
*
G
M
T
T
T
P
P
*
A
S
*
H
O
O
O
E
E
[
I
I
*
R
T
*
*
A
A
V
*
L
-
[
D
Y
I
R
R
T
T
I
*
*
V
V
E
M
E
E
*
*
D
*
*
*
T
N
S
E
C
W
P
R
E
*
*
*
R
S
T
R
*
*
L
E
O
*
*
*
*
I
O
C
*
A
C
*
*
*
*
M
T
P
R
H
*
Y
*
M
*
*
*
O
Y
*
E
E
*
*
*
O
*
*
*
D
*
C
C
*
*
*
D
*
*
*
E
R
*
*
K
*
*
*
E
*
*
*
]
E
*
*
*
*
*
*
]
*
*
*
*
C
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
*
*
*
*
*
*
*
*
*
*
* *
L
*
*
*
*
*
*
*
*
*
*
*
I
O
O
*
O
O
O
O
O
O
O
*
N
F
F
*
F
F
F
F
F
F
O
*
E
F
F
*
F
F
F
F
F
F
N Set to “ON”.