Pioneer VSX-1015-K - Manual (Page 50)

Using the tuner 07
50
En
Saving station presets
If you often listen to a particular radio station, it's
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. This
unit can memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations each. When
saving an FM frequency, the
MPX setting (see page 49) is
also stored.
1 Tune to a station you want to memorize.
See Listening to the radio on page 49 for more on this.
2 Press T.EDIT (TUNER EDIT).
The display shows STATION MEMORY , then a blinking
memory class.
3 Press CLASS to select one of the three classes
then press ST +/– (STATION +/–) to select the station
preset you want.
You can also use the number buttons or the MULTI JOG
dial (front panel) to select a station preset.
4 Press ENTER.
After pressing ENTER , the preset class and number stop
blinking and the receiver stores the station.
Naming station presets
For easier identification, you can name your station
presets.
1 Choose the station preset you want to name.
See Listening to station presets below for how to do this.
2 Press T.EDIT (TUNER EDIT).
The display shows STATION NAME , then a blinking
cursor at the first character position.
3 Input the name you want.
Choose from the following characters for a name up to
four characters long.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!”#$%&’() ∗ +,–./:;<=>?@[ \ ]^_{|} ˜
• Use the MULTI JOG dial (front panel) or the ST +/–
buttons (remote) to select characters.
• Press ENTER to confirm a character. If no character
is input, a space is input.
• The name is stored when ENTER is pressed after
choosing the fourth character.
Tip
• To erase a station name, simply repeat steps 1-3 and
input four spaces instead of a name.
• Once you have named a station preset, you can press
TUNER DISPLAY when listening to a station to
switch the display between name and frequency.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets above if you haven’t done this
already.
1 Press TUNER to select the tuner.
2 Press CLASS to select the class in which the
station is stored.
Press repeatedly to cycle through classes A, B and C.
3 Press ST +/– (STATION +/–) to select the station
preset you want.
• You can also use the number buttons on the remote
control to recall the station preset.
Note
• If the receiver is left disconnected from the AC power
outlet for over a month, the station memories will be
lost and will have to be reprogrammed.
STANDBY/ON
MULTI JOG
LISTENING MODE SELECT
ENTER
PHONES
TUNER CONTROL
TUNER
EDIT
SYSTEM
SETUP RETURN
PTY
SEARCH EON MCACC SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI JOG MULTI JOG
TUNING/
STATION BAND MPX TONE
ACOUSTIC
EQ
DIALOG
ENHANCEMENT
MULTI CH
IN
SIGNAL
SELECT EXTENDED
MODE SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
INPUT ATT FL DIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE INPUT
SELECT
DVD/LD TV/SAT DVR/VCR TV CONT
CD CD-R/TAPE TUNER RECEIVER
+10
INPUT ATT FL DIMMER SR DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
INPUT
SELECT TV CH
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
REC MUTE
TV VOL
ENTER
REC STOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
A
B C D E
ST ST
VSX_1015.book.fm 50 ページ ２００５年３月７日 月曜日 午後７時０分