Pioneer VSX-1015-K - Manual (Page 55)

Controlling the rest of your system 09
55
En
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
1 While pressing the RECEIVER button, press and
hold the 1 button.
The remote LCD display shows SETUP .
2 Press the MULTI CONTROL button for the
component you want to control.
The LCD on the remote displays the component you want
to control.
• You can’t assign the RECEIVER button.
3 Use / (cursor left/right) to select LEARN then
press ENTER.
PRES KEY
shows in the LCD display.
• To exit or cancel press RECEIVER .
4 Point the two remote controls towards each
other then press the button that will be doing the
learning on this receiver’s remote control.
PRES KEY
starts flashing to indicate the remote is ready
to accept a signal.
• The remote controls should be 3–5 cm apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal
to this receiver’s remote control.
For example, if you want to learn the playback control
signal, press and hold
for a couple of seconds. The
LCD display will show OK if the operation has been
learned.
If for some reasons the operation hasn’t been learned the
LCD will display
ERROR briefly and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows
OK .
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press the RECEIVER button to exit and store the
operation(s).
Note
• Some commands from other remote controls cannot
be learned, but in most cases the remotes just need
to be moved closer together or farther apart.
• If the remote LCD shows ERROR , it may also mean
the memory is full. See Erasing one of the remote
control button settings below to erase a programmed
button you’re not using to free up more memory.
• TV CONTROL buttons ( TV , TV VOL +/– , TV CH +/–
and INPUT SELECT ) can only be learned after
selecting TV CONT .
3 – 5 cm
+10
INPUT A TT FL D IMMER
SR DISC
RECEIVER
MUL TI C ONTROL
SOURCE
INPUT SELECT SETUP ENTER TV C O N T R O L
RECEIVER C
O NTROL
SHIFT
VO L
DV D /L D T V /S A T D V R/V C R T V C ONT
CD
TUNE TUNE ST
ST
ST ANDR AD
LEVEL
EFFECT
TEST T O NE CH SELECT AD V. SURR
STEREO
SLEEP
INPUT SELECT
TV C H
DT V ON/OFF TUNER DISPL AY MPX AUDIO CH RETURN SUB TITLE
MIDNIGHT/ LO U D N ES S
DT V INFO
REC
M U T E
TV V O L CD-R/T APE
TUNER
RECEIVER ENTER
REC ST OP HDD CH
CH DV D
D. A C C E S S
TO P MENU DT V MENU
CL ASS MENU BAND RETURN
GUIDE T. E D IT
MC A C C SETUP
RECEIVER
+10
INPUT ATT FL DIMMER SR DISC
RECEIVER
MULTI CONTROL
SOURCE INPUT
SELECT
ENTER
TV CONTROL
RECEIVER CONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TV CONT
CD
ST ST
THX
SLEEP DIALOG E
AUTO SURR
STANDARD ADV.SURR STEREO
INPUT
SELECT TV CH
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CH SEL
ACOUSTIC
EQ
REC MUTE
TV VOL
CD-R/TAPE TUNER RECEIVER
ENTER
REC STOP
HDD
CH CH
DVD
D.ACCESS
TOP MENU
CLASS
MENU
BAND
RETURN GUIDE
T.EDIT
SYSTEM
SETUP
RECEIVER
TUNE
TUNE
A
B C D E
VSX_1015.book.fm 55 ページ ２００５年３月７日 月曜日 午後７時０分