Panasonic AJ-HD150 - Manual (Page 75)

– 75 –
USER menu
<AUDIO> (continued)
Item Setting
No.
Superimposed
No.
Superimposed Description
display display
745 MONI CH 0000 MANU
SEL 0001 AUTO1
0002 AUTO2
0003 AUTO11
0004 AUTO21
746 MONI AUTO 0000 L/R
SEL 0001 L
0002 R
747 MONI SEL 0000 OFF
INH 0001 ON
0002 ON1
748 AUDIO PB 0000 DIS
VR 0001 ENA
749 ANA CH1 0000 CH1
SEL 0001 CH5
750 ANA CH2 0000 CH2
SEL 0001 CH6
751 ANA CH3 0000 CH3
SEL 0001 CH7
752 ANA CH4 0000 CH4
SEL 0001 CH8
753 SD SDI CH1 0000 CH1
SEL 0001 CH5
754 SD SDI CH2 0000 CH2
SEL 0001 CH6
755 SD SDI CH3 0000 CH3
SEL 0001 CH7
756 SD SDI CH4 0000 CH4
SEL 0001 CH8
The underline on the setting item denotes the initial setting.
This selects the monitor output.
0: The output is as selected in MONITOR SELECT.
1: The cue signal is automatically output in all tape modes
except that PCM AUDIO is output over the –1 to +1 range.
2: The cue signal is automatically output in all tape modes
except in the play mode in which PCM AUDIO is output.
3: The cue input signal is automatically output when the unit is
in the EE mode in addition to AUTO1.
4: The cue input signal is automatically output when the unit is
in the EE mode in addition to AUTO2.
If a setting other than MANU has been selected for setup
menu item No.745 (MONI CH SEL), the CUE signal is
automatically sent to the monitor output in accordance with
the operation mode but this item selects the monitor channel
which will be automatically switched to CUE.
0: The CUE signal is output to both the left and right channels.
1: The CUE signal is output to the left channel only.
2: The CUE signal is output to the right channel only.
This selects whether to enable or disable the MONITOR
SELECT button on the front panel.
0: The button’s operation is enabled.
1: The button’s operation is disabled.
2: In the FULL display mode, the button’s operation is
disabled; operation is enabled in the FINE display mode
only.
This selects whether the playback level controls are to work in
the EE mode when INT SG has been selected as the setup
menu item No.700 (AUDIO IN SEL) setting.
0: The INT SG output level is fixed at UNITY.
1: The INT SG output level can be varied using the playback
level controls.
This selects the signals to be output to analog output CH1.
0: The CH1 signals are output.
1: The CH5 signals are output.
This selects the signals to be output to analog output CH2.
0: The CH2 signals are output.
1: The CH6 signals are output.
This selects the signals to be output to analog output CH3.
0: The CH3 signals are output.
1: The CH7 signals are output.
This selects the signals to be output to analog output CH4.
0: The CH4 signals are output.
1: The CH8 signals are output.
This selects the signals to be output to SDI output CH1.
0: The CH1 signals are output.
1: The CH5 signals are output.
This selects the signals to be output to SDI output CH2.
0: The CH2 signals are output.
1: The CH6 signals are output.
This selects the signals to be output to SDI output CH3.
0: The CH3 signals are output.
1: The CH7 signals are output.
This selects the signals to be output to SDI output CH4.
0: The CH4 signals are output.
1: The CH8 signals are output.
Setup menus