Nilfisk-Advance America RS 1300 - Manual (Page 50)

ENGLISH INSTRUCTIONS FOR USE
28 33015124(3)2008-02 RS 1300
USING THE CAMERA KIT (optional)
To turn on the video system (1, Fig. AX) and the cameras (4 and 5), press the switch (2) when the ignition key (24, Fig. D) is
inserted.
When the reverse gear is engaged, the video system and cameras turn on automatically.
For the functions of other switches on the right side of the display, refer to the camera kit Manual.
AFTER USING THE MACHINE
After working, before leaving the machine, perform the following operations.
Engage the parking brake with the lever (13, Fig. E).
Turn off the dust control system water pump with the switch (27, Fig. D).
If open, close the dust control system taps (10, 11, 12, Fig. E).
Lift the 3rd broom by pushing the joystick (46, Fig. D) rearward.
Lift the suction inlet and side brooms by pressing the push-button (38, Fig. D).
Turn the engine throttle lever (16, Fig. E) to idle, and hold it in this position for a few minutes to let the system stabilize.
Check that the hopper (6, Fig. G) is lowered and that the warning light (3, Fig. D) is off.
If necessary, bring the 3rd broom from opened position to closed position according to the following procedure:
With the spring-return switch (34, Fig. D), check that the 3rd broom arm extension (22, Fig. G) is to the right end of stroke.
Otherwise bring it to the above-mentioned position by pressing and holding the switch (34, Fig. D).
Shift the 3rd broom arm (23, Fig. G) from opened position to closed position by pushing the joystick (46, Fig. D) to the left.
The shifting operation will stop automatically when the end of stroke is reached.
WARNING!
It is possible to shift to the left or to the right the 3rd broom arm (23, Fig. G) safely, only when the arm extension
(22) is to the left or right end of stroke.
In this situation the arm shifting is limited by proper safety devices.
Otherwise, an excessive shifting can damage the machine or affect its stability.
It is therefore advisable to bring always the 3rd broom arm extension (22, Fig. G) to the left or right end of
stroke.
WARNING!
It is possible to bring the 3rd broom arm (23, Fig. G) to closed position, only when the arm extension (22) is to
the right end of stroke.
Stop the 3rd broom and side broom rotation with the switch (29, Fig. D). When the brooms turn off, the suction fan turns off
automatically.
Clean the hopper, the fi lters and the suction pipe, check the gaskets and lubricate the suction fan bearings, as shown in the
Maintenance chapter.
Turn off the engine, by turning the ignition key (24, Fig. D) counterclockwise, to the end of stroke, then remove it.
The headlights must be turned off.
Get out of the machine and bring the 3rd broom safety pin from the position (2, Fig. H) (disengaged) to the position (1)
(engaged), by pulling and turning the relevant lever.
DUST CONTROL SYSTEM WATER TANK EMPTYING
When necessary, empty the dust control system water tanks according to the following procedure.
Engage the parking brake (13, Fig. E).
Turn off the engine, by turning the ignition key (24, Fig. D) counterclockwise, to the end of stroke, then remove it.
Operating over the right side of the rear axle, unscrew the water fi lter cover (1, Fig. Z) and remove it together with the fi lter.
Drain all the water from the tanks.
Install the cover (1, Fig. Z) and the fi lter.
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
8.
•
•
9.
10.
11.
12.
13.
1.
2.
3.
4.
5.