NEC XL-6500G - Manual (Page 8)

8
1234567
1234567
1234567
1234567
1234567
1234567
1.PART NAMES AND FUNCTIONS .
1 Breaker Switch
Press the switch to the ON position to turn on the breaker
and press to the OFF position to turn off the breaker.
When abnormal conditions are encountered, the breaker
will trip and turn the projector off.
If the projector will not be used for an extended period of
time, turn off the breaker by pressing the switch to the
OFF position.
2 Remote Sensor
Receives the signal from the supplied remote control
when used in the wireless mode.
3 Power Switch (Main power)
To turn on the main power to the projector press the
switch to the ON position (I). The STANDBY and the RC
READY indicator will light.
In this condition you can start up the projector by pressing
the POWER ON button on the remote control or the
POWER button on the side panel.
Press to the OFF position (0) to turn the main power off.
NOTE: When turning off the main power, first return the
projector to the standby condition by pressing the
POWER OFF button on the remote control or the POWER
button on the side panel and then turn off the main
POWER switch. These procedures are necessary to
protect your projector and the connected equipment.
4 AC INPUT
Connect the supplied power cord here (AC 200-240V).
5 POWER Button
Turns the projector on when the projector is in the
standby condition (Main Power switch must be on and
the STANDBY indicator lit). Turns the projector off after
“- -” on the two digit display is blinking for three min-
utes.
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
,,
,,
@@
@@
PP
PP
This compartment accommodates the remote control.
The remote control serves as the key panel on the
projector when it is plugged and fit in this compartment.
NOTE: Do not turn off the main power while “- -” on the
two digit display is blinking. During this time the lamp is
cooling off.
6 POWER Indicator
Lights up when the projector is turned on.
7 STANDBY Indicator
Lights up when the projector’ s main POWER switch is on.
When the projector is used with the ISS-6020 switcher on
SW1 level or SW2 level mode, this indicator flashes when
the projector is not connected with the switcher correctily
or when the switcher is turned off.
8 RC READY Indicator
Lights up when the projector’s main POWER switch is on.
Flashes when the projector receives a signal from the
remote control.
9 LAMP Indicator
Displays the lamp on or off.
Indicator illuminates—Lamp is turned on
Indicator goes out-Lamp is turned off
0 Two Digit Display
INDICATOR: Displays projector error codes.(“00” in
normal operation)
ON/OFF Switch: Turns the INDICATOR on or off.
A REMOTE 2 Jacks
IN: for the wired remote control.
OUT: for daisy-chaining multiple projectors and operating
them with the same remote control. To do so, connect to a
second projector’ s IN terminal to relay the input at the IN
terminal of the first projector until all the projectors are
connected.
OFF BREAKER ON
XL-6500G
OFF POWER ON
AC INPUT
POWER
ON/STANDBY Indicator
AC INPUT
POWER ON/STANDBY Indicator
lights in green when the projector is turned on and
lights in red when the projector is in standby.
1 1 1 1 1
4 4 4 4 4 3 3 3 3 3 2 2 2 2 2