Roland FP-3 - Manual (Page 42)

42
Chapter 4 Other Functions
Connecting MIDI Devices
About MIDI
MIDI stands for “Musical Instrument Digital Interface,” and
is a worldwide standard for the exchange of performance
data (MIDI messages) and other information among
electronic instruments and computers.
The FP-3 features a MIDI connector and a computer
connector to allow performance information to be exchanged
with external devices. Connecting the keyboard to other
devices with these connectors provides you with an even
greater variety of ways to use your keyboard.
* A separate publication titled “MIDI Implementation” is also
available. It provides complete details concerning the way
MIDI has been implemented on this unit. If you should require
this publication (such as when you intend to carry out byte-
level programming), please contact the nearest Roland Service
Center or authorized Roland distributor.
■ Connectors
fig.04-08
MIDI Out Connector
Sends data about what is being played on the keyboard and
other performance data.
Connect to the MIDI in connector on the external MIDI device.
MIDI In connector
Receives messages sent from external MIDI devices.
Connect to the MIDI Out connector on the external MIDI device.
■ Making the Connections
* To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power
on all devices before making any connections.
1. Turn the volume all the way down on the FP-3
and on the device you’re about to connect.
2. Turn off the power to the FP-3 and to the device
being connected.
3. Connect a MIDI cable (sold separately) between
the MIDI connectors on each device.
4. Switch on the power to the FP-3 and the
connected device.
5. Adjust the volume level on the FP-3 and the
connected device.
6. You should also set the MIDI settings as needed.
Make the settings for the MIDI send and receive
channels (p. 43) and for Local On/Off (p. 43).
■ How to Enjoy MIDI
Recording Data of Performances Played on the FP-3 to a
Sequencer* and Automatically Playing Recorded
Performance Data on the FP-3
Connection example:
Connecting to a sequencer (the Roland MT series, etc.)
fig.04-09.e
→ When connecting a sequencer, we recommend using it with
the settings described below.
• Local Control off (p. 43)
• MIDI Out Mode 1 (p. 44)
When the instrument is turned on, MIDI Out Mode is set
to “1.”
Performing on the FP-3 Using Sounds from Another
Sound Module*
Connection Example: Connecting to a MIDI Sound Module
fig.04-10.e
→ When connecting to a MIDI sound module, we recommend
using the system with MIDI Out Mode set to “2” (p. 44).
When the instrument is turned on, MIDI Out Mode is set to
“1.”
What is a Sequencer?
A sequencer is a device that records the stream of MIDI
messages that is sent out by an instrument. These messages
convey all the details of what has occurred while the
instrument is played; including the timing of notes, their
sound, the force used to play them, and for how long.
Afterwards, you can send the recorded MIDI information
back to the instrument, and it will play automatically.
What is a MIDI Sound Module?
Inside a synthesizer or electronic piano is the section that
actually produces sound, known as the sound module. A
MIDI sound module produces sounds as the result of MIDI
messages sent to it by other devices.
MIDI
Out In
FP-3
In Out MIDI
Sequencer
* The MT-80s has no MIDI
Out connector.
MIDI
Out In
Damper Soft
Pedal Line In
R L (Mono)
Stereo
Line Out
R L (Mono)
Stereo
OUT THRU IN
MIDI
Sound Module
FP-3
MIDI
Out In
Damper Soft
Pedal Line In
R L (Mono)
Stereo
Line Out
R L (Mono)
Stereo