Onkyo Network A/V Receiver TX-NR1010 - Manual (Page 64)

Advanced Operations
En-64
■ Preout to External Amplifier
` No
` Surr Back, Front High, Front Wide
For 9.2-channel playback, select the channel output by
SB/FH/FW EXT AMP jacks. If you select speakers whose
setting in Speaker Configuration is set to “None”, it will be
automatically switched to “80Hz (THX)”.
Note
• If the “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”, Powered Zone 2 cannot be used.
• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
• When the “Powered Zone 2” setting is set to “Yes”, the front
wide speakers cannot be used.
• If the “Powered Zone 2” setting is set to “No”, the “Powered
Zone 3” setting cannot be selected.
• “Preout to External Amplifier” is not available in either of the
following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Powered Zone 2” setting is set to “Yes”.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` 1ch:
Audio signal is outputted from SW1 jack only.
` 2ch :
Audio signal is outputted from SW1 and SW2 jacks.
` No
■ Front
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center *1 , Surround *1*2
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Front Wide *1*3*4*6*8 , Front High *1*3*5*6*7*8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Surround Back *1*3*5*6*8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
Note
*1 “Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2 When the “Powered Zone 3” setting is set to “Yes” and
Zone 3 is turned on, this setting cannot be selected.
*3 This setting cannot be selected if the “Speakers Type(Front)”
setting is set to “Bi-Amp” or “Digital Crossover”.
*4 When the “Powered Zone 2” setting is set to “Yes”, this
setting cannot be selected.
*5 When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, this setting cannot be selected.
*6 If the “Surround” setting is set to “None”, this setting cannot
be selected.
*7 When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be selected.
*8 If the “Preout to External Amplifier” setting is enabled for
these speakers, “None” cannot be selected.
This setting is set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup ( ➔ page 39 ).