Onkyo DR-S2.0 - Manual (Page 64)

64
INPUT SELECTOR
MODE
AU DIO
DVD
TV
TA/MD
LIS TEN ING MODE
A.C TR L
T – D STER EO
SU RR
TIT LE MEN U
SET UP
TV/V CR
RET URN
CH
TUN VOL ENTER
REPEAT MUTING
A – B DIMMER
STNBY ON
SLE EP
SEND LEARN
Programming the Remote Controller to Your TV
One of the TV’s
remote control
buttons
INPUT SELECTOR
MODE
AU DIO
DVD
TV
TA/MD
LIS TEN ING MODE
T – D STER EO
STNBY ON
SLE EP
SEND LEARN
TV
CH
TUN
VOL
SET
UP
TV/V
CR
MUTING
STNBY ON
4
• Flashes twice when the programming is
successful.
• Flashes three times if the programming has
failed.
• Flashes six times if the programming is failed
because the data capacity of the
programmable button has been exceeded.
TV buttons whose data size overwhelms the
capacity of the programmable buttons are
unable to be used for programming. Using the Programmed Buttons
Press MODE TV first, then press the
programmed TV operation buttons.
Resuming the factory settings for all the
programmable buttons
1 Press and hold MODE TV, then press SEARCH twice.
The SEND/LEARN indicator flashes twice, then lights
steadily.
Proceed to the next step within 30 seconds.
2 Press MODE TV.
• When the factory settings resume, the SEND/LEARN
indicator flashes twice.
• If failed, the SEND/LEARN indicator flashes three times.
In this case, no change has been made to the
programmable buttons.
If the programmed buttons do not operate properly
• If the SEND/LEARN indicator doesn’t light up when you press one of
the programmed buttons, reprogram the button.
• If the remote controller operates only at a short distance or there is
a slow response from the TV, check the batteries.
If the batteries are not weak, the pressed button is not properly
programmed. Reprogram the button.
• If the remote controller remains without batteries for 10 minutes or
more, the programmed data will be erased. In such a case, install
new batteries, then reprogram the buttons.
Press one of the programmable
buttons on the DVD Receiver’s
remote controller.
The SEND/LEARN indicator goes off while
the button is pressed, then lights up again.
Proceed to the next step within 30
seconds.
To select another programmable button
Press one of the other programmable buttons
within 30 seconds.
Press and hold the desired TV’s
remote control button until the
SEND/LEARN indicator flashes.
If the function is successfully copied, the
SEND/LEARN indicator flashes twice.
3
INPUT SELECTOR MODE
AU DIO
DVD
TV
TA/MD
LIS TEN ING MODE
T – D STER EO
STNBY ON
SLE EP
SEND LEARN
INPUT SELECTOR MODE
AU DIO
DVD
TV
TA/MD
LIS TEN ING MODE
A.C TR L
T – D STER EO
SU RR
TIT LE MEN U
SET UP
TV/V CR RET URN
CH
TUN VOL ENTER
REPEAT MUTING
A – B DIMMER
STNBY ON
SLE EP
SEND LEARN
Lights up again shortly after going off
Programming another function to the
programmed button
Carry out the steps from 1 to 4.
The previous function will be erased when the programming is
successful.
Resuming the factory setting for a
particular programmable button
After step 2, press the programmable button you wish to
resume to the factory setting twice.
• When the factory setting resumes, the SEND/LEARN
indicator flashes twice.
• If failed, the SEND/LEARN indicator flashes three times.
In this case, no change has been made to the
programmable button.