Document Outline

• Title Page
• Warranty
• Table of Contents
• List of Figures
• List of Tables
• General Safety Summary
  • To Avoid Fire or Personal Injury
    • Use Proper Power Cord
    • Use Proper Power Source
    • Ground the Product
    • Use Proper Fuse
    • Operate Only Within a Suitable Enclosure
    • Provide Proper Ventilation
    • Use in a Proper Environment
    • Observe All Terminal Ratings
  • Safety Terms and Symbols
    • Terms in this Manual
    • Terms on the Product
    • Symbols on the Product
• Preface
  • This Manual
  • Contacting Tektronix
    • Phone
    • Address
    • Web site
    • Sales support
    • Service support
    • Technical support
    • This phone number is toll free in North America. After office hours, please leave a voice mail message. Outside North America, contact a Tektronix sales office or distributor; see the Tektronix web site for a list of offices.
• Getting Started
  • Unpacking
  • Mechanical Installation
  • Connecting the 764 to Your System
    • (1) Digital Audio Inputs and Loop-Throughs
    • (2) Time Code Inputs
    • (3) Reference Inputs
    • (4) VGA Video Output
    • (5) RS-232 Communications Port
    • (6) Optional Serial Video Loop-Through
    • Headphones
  • Supplying Power
  • Initial Power Up and Configuration
• Operating Basics
  • Overview
    • Monitoring an Audio Program with the Audio View
    • Session Reports
    • Monitoring the Ancillary Data
    • Other Features
  • Front-panel Controls
    • (1) POWER switch
    • (2) VIEW Selection buttons.
    • (3) PHASE DISPLAY and SESSION buttons
    • (4) METER SCALE buttons
    • (5) Multi-function knob.
    • (6) MENU button
    • (7) Soft buttons
    • (8) CLEAR MENU button
    • (9) Headphone VOLUME control
    • (10) Display BRIGHTNESS control
  • The Level Meters
    • (1) Meter Ballistics
    • (2) Scale Units (dBFS or dBr).
    • (3) Peak Program level.
    • (4) Test Level
    • (5) Variable scale
    • (6) Mute indicator (and other messages)
    • (7) Meter bar labels
    • (8) True peak indicators
    • (9) Clipping flag
    • Configuring the Level Meters
    • Sum and Difference Bars
  • The Phase Display
    • The Lissajous Pattern
    • The Correlation Meter
    • AGC
  • The Session Display
    • Features of the Session Display
    • Session Statistics
  • Session Reports
  • The Channel Status View
  • The User Data View
  • Saving and Restoring Setups
    • Saving a Setup
    • Restoring a Setup
    • Editing a Setup
• Reference
  • Level Meters
    • Meter Ballistics and Alignment Levels
    • In-Bar Warning Messages
      • INPUT UNLOCKED
      • CODE ERR
      • PARITY
      • LOW CONF
      • V BIT
  • Correlation Meter Algorithm
  • Selecting Headphone Channels
  • Submenus
    • The Level Meters Submenu
      • Display Mode
      • Ballistics
      • Peak Hold Time
      • Peak Program Level (dBFS)
      • Test Level (dBFS)
      • Set 0 dB Mark to
      • Consecutive FS Samples for CLIP
      • Consecutive “0” Samples for MUTE
      • CLIP/MUTE Hold Time (sec)
      • Ignore Validity Bit
      • Suppress Sync Loss Flags
    • The De-emphasis Submenu
    • The Phase Display Submenu
    • Headphones Submenu
    • Input Submenu
    • Time Code Submenu
    • Serial Port Submenu
      • Flow Control
      • Baud Rate
      • Copy
      • Peak Reading Interval (sec).
    • Save Setups Submenu
    • Restore Setups Submenu
    • Screen Saver Submenu
    • Service Submenu
  • Using the RS-232 Port
    • Cable Requirements
    • Communication Examples
    • Outputting a Session Report
    • Remote Control Commands
    • Command Syntax
    • General Commands
    • GET Commands
    • PRESS Commands
    • MENU Commands
• Appendix A: Specifications
• Appendix B: Error/Warning Messages
  • Channels not synchronized
  • CLIP
  • CODE ERR
  • CRC Error
  • De-emp
  • INPUT UNLOCKED
  • Interpolation OFF
  • LOW CONF
  • MUTE
  • No Reference Signal
  • No Video Input (Option 01 only)
  • NOT PRESENT (Option 01 only)
  • PARITY
  • SYNC ERR
  • V BIT
• Appendix C: Options
  • Embedded Audio Input (Option 01)
    • Operating Information
      • Connect the Instrument
      • Select the Digital Video Input and Audio Channel Group
      • Changes to the Session Statistics Display
      • Additional Error/Warning Messages
      • Configure the Meters
      • Configure the Phase Display
      • Changes to the Session Statistics Display
      • Additional Error/Warning Messages
  • Analog Line Output (Option 02)
    • Configuring the Output
    • Connecting the Instrument
      • High-level, Balanced Output
      • Low-level, Unbalanced Output
  • Power Cords
• Glossary
• Index