Aqua-Pure CBF150 - Manual (Page 8)

IMPORTANT NOTES IMPORTANT NOTES
• Damage due to heat is not covered under the manufacturer’s warranty and will void the warranty.
• The use of fl exible drain lines are prohibited in some states, check with your local code offi cer for requirements. Distance and height affects the perfor-
mance of the drain line to discharge at the proper rate to effectively backwash the fi lter media. The following are guidelines for drain line size installa-
tion. Do not bend the drain line too sharply if using fl exible tubing. Secure the drain line over the discharge line to prevent splashing or blow out during
regeneration. Do not use garden hose or vinyl tubing as a drain line as this may cause a failure to regenerate properly.
• You will need the serial number and model number of the unit to have certain parts replaced under warranty. Please preserve the shipping carton in case
the factory technical support services personnel request to verify your claim of missing or damaged parts.
• Activated carbon requires four (4) hours of saturation and Filter-Ag two (2) hours of saturation to prevent media from washing to the waste drain prior
to start-up.
Step 1
Inspect and open factory sealed box to ensure all components required for installation are present. If media was ordered, verify the amount and type of
fi lter media (ordered separately) is correct.
Step 2
Remove CBF Series Residential Backwash Filtration System from shipping carton and inspect to ensure there is no damage to product from shipping.
Inspect any packing for components that have been attached for shipping before discarding. If any items intended for installation are missing at this
time contact your Dealer/Installer or our Customer Service Department at 1-800-222-7880 to notify them of this situation and provide the model number
and serial number.
Step 3
For Threaded Tank Models: CBF100, CBF150, CBF200: Follow the steps to center the distributor tube and load the fi lter media into the media tank to
ensure the successful installation of your CBF Series Residential Backwash Filtration System.
a. Remove the control valve by rotating the valve head assembly to the left or counter-clockwise and set aside to reassemble after media is loaded into
the tank.
b. Tilt media tank to a 45 degree angle until gravel shifts to the side of the tank and dimple at bottom of media tank is visible. This will allow you to place the
distributor tube basket assembly in the dimple on the bottom of the media tank.
c. Place media tank back in upright position and ensure gravel at the bottom of the media tank is level. Place red plastic cap on the distributor tube that is
provided in the parts bag.
d. Locate the fi lter media that will be used in the backwashing fi lter and load into the media tank. Note: fi ll only to the labeled line on the outside of
the media tank. Refer to the Specifi cation section on page 5-1 for the correct quantity for your CBF Series Residential Backwash Filtration System.
Use a clean rag to wipe the opening of the media tank to remove any dust or sediment before moving to the next step.
Dome Hole Tank Models: CBF100DM, CBF150DM, CBF200DM:
a. Add media through fi llport cap located on tank using funnel (See FILLING MEDIA TANK below). Fillport cap can be removed by turning a quarter turn
counter clockwise.
CAUTION CAUTION
To reduce the risk associated with skin, eye, and respiratory tract irritation from
dust from fi lter media during installation:
• Gravel and several types of fi lter media may be used in this product, depending upon the
application. During installation, dust may cause irritation to skin, eyes, and respiratory
tract, and may affect lungs.
• Utilize a NIOSH-approved dust fi lter mask and appropriate eye protection when handling
and pouring gravel and fi lter media.
• To request an MSDS relating to this product, call 203-238-8965 or go to www.3M.com ,
select country, and use the search engine to search MSDS. For emergencies, call 800-
364-3577 or 651-737-6501 (24 hours).
b. Reinstall fi llport cap by turning a quarter turn clockwise.
c. If bypass valve assembly is not factory pre-installed, attach using clips and screws.
d. Using a clean dry rag, wipe the opening of the media tank to remove any dust or residue from the opening to receive the control valve. Attach the
valve head to the media tank by rotating the valve head assembly to the right (clockwise).
2-2
FILLING MEDIA TANK