Asus Pundit-PH3 - Manual (Page 56)

4 - 6 4 - 6 4 - 6 4 - 6 4 - 6 C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o
2 . 2 . 2 . 2 . 2 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
3 . 3 . 3 . 3 . 3 . C P U a n d C h a s s i s f a n c o n n e c t o r s C P U a n d C h a s s i s f a n c o n n e c t o r s C P U a n d C h a s s i s f a n c o n n e c t o r s C P U a n d C h a s s i s f a n c o n n e c t o r s C P U a n d C h a s s i s f a n c o n n e c t o r s
( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 )
( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 )
The fan connectors support cooling fans of 350 mA~740 mA (8.88 W
max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 before using Serial ATA hard disk drives.
• When using the connectors in standard IDE mode, you can connect the
primary (boot) hard disk drive to any of the SATA connectors.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
®
SATA connectors
SATA1
SATA2
GND
RSA
T A_TXP1
RSA
T A_TXN1
GND
RSA
T A_RXP1
RSA
T A_RXN1
GND
GND
RSA
T A_TXP2
RSA
T A_TXN2
GND
RSA
T A_RXP2
RSA
T A_RXN2
GND
®
Fan connectors
CPU_FAN1 CHA_FAN1
GND CPU F
AN PWR
CPU F
AN IN
CPU F
AN PWM GND Rotation +12V