KEPCO ATE-DMG SERIES - Manual (Page 71)

ATE-DMG 042314 B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 INTRODUCTION This appendix defines the SCPI subsystem commands and queries used with the
ATE Power Supply. Subsystem commands are defined in PAR. B.2 through B.96, arranged in
groups as they appear in the tree diagram, Figure 3-7. Table B-1 provides a quick reference of
all SCPI subsystem commands and queries used in the Interface Card.
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND PAR. COMMAND PAR.
ABORt B.2 READ:VOLT? B.49
CAL:VOLT:GAIN B.3 [SOUR:]CURR[:LEV][:IMM][:AMP], ? B.50, B.51
CAL:CURR[:DATA] B.4 [SOUR:]CURR:LIM:HIGH, ? B.52, B.53
CAL:PASS, ? B.5 [SOUR:]CURR:PROT[:LEV], ? B.56, B.57
CAL:CURR:GAIN B.6 [SOUR:]CURR:PROT:CLE B.58
CAL:STAT, ? B.7, B.8 [SOUR:]CURR:PROT:TRIP B.59
CAL:VOLT:LEV B.9 [SOUR:]CURR[:LEV]:TRIG[:AMP], ? B.60, B.61
CAL:VOLT[:DATA] B.10 [SOUR:]VOLT[:LEV][:IMM][:AMP], ? B.62, B.63
CAL:ZERO B.11 [SOUR:]VOLT[:LEV]:TRIG[:AMP]? B.64, B.65
DIAG:EXT, ? B.12, B.13 [SOUR:]VOLT:LIM:HIGH, ? B.66, B.67
DISP:CONT, ? B.14, B.15 [SOUR:]VOLT:PROT:LEV, ? B.70, B.71
DISP:MODE, ? B.16, B.17 [SOUR:]VOLT:PROT:CLE B.72
DISP:TEXT, ? B.18, B.19 [SOUR:]VOLT:PROT:TRIP? B.73
INIT[:IMM] B.20 [SOUR:]FUNC:MODE? B.74
INIT:CONT, ? B.21, B.22 STAT:OPER:COND? B.75
INST:STAT B.23 STAT:OPER:ENAB, ? B.76, B.77
[SOUR:]LIST:CURR, ? B.24, B.25 STAT:OPER[:EVENT]? B.78
[SOUR:]LIST:CURR:PROT, ? B.26, B.27 STAT:PRES B.79
[SOUR:]LIST:DWELL, ? B.28, B.29 STAT:QUES[:EVENT]? B.80
[SOUR:]LIST:IND, ? B.30, B.31 STAT:QUES:COND? B.81
[SOUR:]LIST:SEQ:NEXT, ? B.32, B.33 STAT:QUES:ENAB, ? B.82, B.83
[SOUR:]LIST:SEQ:START, ? B.34, B.35 SYST:ERR? B.84
[SOUR:]LIST:VOLT, ? B.36, B.37 SYST:ERR:CODE? B.85, B.86
[SOUR:]LIST:VOLT:PROT, ? B.38, B.39 SYST:KLOCK, ? B.87, B.88
MEAS:CURR? B.40 SYST:LANG, ? B.89, B.90
MEAS:VOLT? B.41 SYST:PASS CEN, DIS B.91, B.92
OUTP[:STAT], ? B.42, B.43 SYST:PASS:STAT B.93
OUTP:PROT:DEL, ? B.44, B.45 SYST:SEC B.94
PROG:STAT, ? B.46, B.47 SYST:SET B.95
READ:CURR? B.48 SYST:VERS? B.96