Blue-White Sonic-Pro S4 Ultrasonic Flowmeters - Manual (Page 22)

Page 21 Sonic-Pro
Byte Bit Type No. of Bytes
1 0 Contact Closure 1 0: CC OFF, 1:CC ON
1 Contact Closure 2 0: CC OFF, 1:CC ON
2 Reserved
3 Reserved
1
4 Reserved
5 Reserved
6 Reserved
7 Reserved
2 0 Reserved
1 Reserved
2 Reserved
3 Reserved
1
4 Reserved
5 Reserved
6 Reserved
7 Reserved
3 Flow Rate double 8 Current flow rate value.
11 Totalizer double 8 Current totalizer value.
19 Fault Number Table char 6 Fault number table upto six faults.
25 Speed of Sound unsigned long 8 Current SOS value.
33 Goodness Of Meas. unsigned char 1 Current GOM - 1 to 4.
34 Reserved unsigned char 1
35 4 - 20mA Flow unsigned char 1 4 to 20mA current output
36 Reserved unsigned char 1
37 Flow Frequency unsigned char 8 Frequency output
45 Firmware Version unsigned char 8 8 ASCII characters. A11.22.33
53 Log Entry unsigned char 86 Log Entry String
Eg: 2013/12/29 09:15:00 FR 0.0000 TL 0.00
Description
Page 22 Sonic-Pro
6.4.4
Anybus
Comm.
Menu
There are five different Anybus communications modules that can be installed in the S4
meter. Each optional module uses a different communications protocol.
6.4.3.1
CC Assigned to
Monitor Totalizer When in the Relay A or Relay B menu, selecting and then exiting the Monitor Totalizer
menu will assigned that relay to monitor the accumulated to flow value. The following
functions are possible:
! Set a Batch Amount total flow value which when reached, will energize the relay.
! Set the Contact Timer(s) for the number of seconds (0-999) that the relay will remain
energized.
When either of the relays are energized, the display back-light will turn blue.
Monitor Totalizer Batch Amt. B
0
Enter Value
Contact Timer(s) B
0
Enter Value
6.4.3.2
CC Assigned to
Monitor FAULTS
When in the Relay A or Relay B menu, selecting and then exiting the FAULTS menu will
assign that relay to energize when any of the following fault conditions exist.
Ÿ FAULT 11 - Transducers are not connected or there is no fluid in the pipe.
Ÿ FAULT 12 - The allowable SOS (Speed Of Sound) error set-point has been exceeded.
Ÿ FAULT 21 - The configuration data is not valid.
The display back-light will turn red when there is a FAULT condition.
Faults B
Protocol
Anybus Communications Options
Profibus DPV DB9F
Modbus RTU
Modbus TCP
Industrial Ethernet/IP
Profinet IO
Up to 12 Mbit/s
RJ45 10/100 Mbit/s full/half duplex
Network Connector Baud Rate
DB9F
RJ45
RJ45
Up to 12 Mbit/s
10/100 Mbit/s full/half duplex
100 Mbit/s full duplex
Anybus Type
Modbus RTU
Profibus DPV1
Modbus TCP
Ethernet
Profinet
None
Address
Modbus RTU
Profibus DPV1
Modbus TCP
Ethernet
Profinet
None
0
Enter Value
0
Enter Value
IP SET
192.168.234.123
OK CANCEL
IP SET
192.168.234.123
OK CANCEL
IP SET
192.168.234.123
OK CANCEL
Select the module being used and enter the Port Address (for Profibus DPV or Modbus RTU
modules) or the IP ADDRESS ( for Modbus TCP, Industrial Ethernet/IP or Profinet IO
modules.
Use the following Anybus mapping structure to communicate with the module and monitor the
flowmeter. There are no send commands available.
Optional Anybus
Communications
Module
Communications
Cable Grommet
Industries, Ltd. Industries, Ltd.
ProSeries
by Blue-White Ind.
d
Industries, Ltd. Industries, Ltd.
ProSeries
by Blue-White Ind.
d