Alpine IVA-D105 - Manual (Page 41)

39
-EN
+01GB05IVAD105.fm
ALPINE IVA-D105 68-08564Z59-A (EN)
Display Setup Operation
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [ ] of DISPLAY SETUP.
The DISPLAY setup screen appears.
3
Touch [ ] or [ ] etc., of the desired item to change
its setting.
Setting items:
TILT* / OPEN/CLOSE* / VISUAL EQ / DIMMER /
DIMMER LOW LEVEL / AUTO BACKGROUND /
BACKGROUND / DATA DOWNLOAD / BASE COLOR /
PULSETOUCH / SCREEN ALIGNMENT
* These functions are adjustable while driving.
4
Touch [RETURN] to return to the previous screen.
• Immediately after changing the settings of Display Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF.
Otherwise, the settings may not be changed.
Adjust the monitor’s angle (between 40 and 105 degrees) for optimum
visibility.
Setting item: TILT
Setting range: 10 adjustable angles are available.
• If the monitor touches an obstacle, remove the obstacle.
• The screen color will vary when viewed at certain angles. Adjust the
screen angle for the best viewing position.
• If the voltage of the vehicle's battery power is low, the screen may
blink when the screen angle is changed. This is not a malfunction.
Setting item: OPEN / CLOSE
Setting content: MANUAL / FULL / CLOSE
Backlighting is provided by a fluorescent light built into the liquid
crystal panel. The illumination control adjusts the brightness of the
backlighting based on the car ambient lighting for easier viewing.
Setting item: DIMMER
Setting content: OFF / ON / AUTO
• When ON or AUTO is set, the setting is also applied for the button
lighting in “Adjusting the Dimmer of Button Lighting at Night”
(page 36).
You can adjust the brightness of the backlight (LOW). This function
could be used, for instance, to change the screen brightness while
travelling at night.
Setting item: DIMMER LOW LEVEL
Setting content: -15 to +15
You can adjust the level between -15 and +15.
DISPLAY Setup
To display the Display mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the Display mode operation has been
released. Engaging the parking brake can reactivate the Display
mode, as long as the car's ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3), of
“To display the Display mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Display mode screen.”
The following steps 1 to 4 are common operations to each
“Setting item” of DISPLAY Setup. Refer to each section for
details.
Adjusting the Monitor Angle
Setting Automatic Opening/Closing of the
Monitor
MANUAL: The monitor is manually opened or closed by
pressing OPEN.
FULL: The monitor automatically opens and closes when
the ignition key is turned to the “ACC” or “ON/OFF”
position.
CLOSE: The monitor automatically closes when the ignition
key is turned OFF.
Setting the Brightness of the Backlighting
OFF: Deactivate Auto Dimmer mode to keep the background
illumination of the monitor bright.
ON: Keep the background illumination of the monitor dark.
AUTO: Adjust the brightness of the background illumination of
the monitor automatically to the brightness of the car
interior.
Adjusting the Minimum Level of Backlight
+01GB00IVAD105.book Page 39 Monday, January 15, 2007 4:02 AM