Alpine IVA-D105 - Manual (Page 52)

50
-EN
+01GB06IVAD105.fm
ALPINE IVA-D105 68-08564Z59-A (EN)
Adjusting the DVD Level
The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.
Setting item : DVD LEVEL
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
Adjust the level by touching [ ] or [ ] of the desired
adjusting mode.
The level can be adjusted in the range of –5 to +5.
Storing Settings in the Memory
Adjustment or setting contents can be stored.
Contents that can be stored vary depends on the audio processor used.
Setting item : USER PRESET
1
Touch [ ] or [ ] of USER PRESET to select any one
of the preset buttons (P-1 through P-6).
2
Touch [MEMORY].
The setting contents are stored.
• The stored contents will not be deleted even when the battery power
cord is detached.
Touch [ ] or [ ] of A.PROCESSOR to select the preset
memory you want to recall from P-1 through P-6.
• It takes a few moment to recall the preset memory.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded
on two channels to achieve Dolby Pro Logic II surround sound. For
two-channel Dolby Digital and DTS signals, there is also a “REAR
FILL” function for outputting the signals of the front channel to the rear
channel.
Setting item : DOLBY PLII/REAR FILL
Touch [ ] or [ ] of DOLBY PLII/REAR FILL to select the
desired mode.
If PL II MUSIC is selected, the center width can be adjusted with
following operations.
This function offers the optimum vocal position by adjusting the
center channel position between the center speaker and the L/R
speaker. (The adjustments established in “Adjusting the
acoustic image (BI-PHANTOM)” (page 49) are ineffective while
this function is activated.)
Touch [ ] or [ ] of CENTER WIDTH CONT. to adjust the
level.
The level can be adjusted between 0 to 7. When the level
increases, the center channel position moves from the
center speaker position to both sides.
Touch [OFF] of CENTER WIDTH CONT. to turn off the
center width control.
• This adjustment is effective when the setting of the center speaker is
SMALL or LARGE in the speaker setup settings.
• “REAR FILL” function
Depending on the input signals, the sound may only be output from
the front speakers. In this case, the “REAR FILL” function can be
used to output signals from the rear speakers as well.
• If REAR FILL is set, 192kHz, 96kHz, etc., contents are down sampled
to 48kHz.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 44).
• This function only works with two-channel signals. This operation is
ineffective when 5.1-channel DTS or Dolby Digital signals are input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound is
unchanged in the rear fill setting because REAR MIX is given priority
during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• Touching [RETURN] will return to the previous screen.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2 or
3 channels.
Setting item : PCM MODE
Touch [ ] or [ ] of PCM MODE to select 2 CH or 3 CH.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 44).
Recalling the Preset Memory
PL II MOVIE: Suits the stereo TV shows and all programs
encoded in Dolby Surround. It improves the
sound field directivity to near that of discrete
5.1-channel sound.
PL II MUSIC: Can be used for all stereo music recordings, and
provides a wide, deep sound field.
OFF: Turns DOLBY PL II function to OFF.
PANORAMA:
(BassEngine
only) Widens the soundstage of the front stereo Image
to extend to the surround speakers.
• The setting can be made only when an external audio
processor is connected.
When the Bass Engine mode is set, the level setting is fixed to
“3.”
2CH: 2ch output (L/R)
3CH: 3ch output (L/R/CENTER)
+01GB00IVAD105.book Page 50 Monday, January 15, 2007 4:02 AM