Audio-Technica AEW-T1000A - Manual (Page 11)

Artist Elite ® 4000 & 5000 Series Professional UHF Wireless Systems
11
Fig. E AEW-R4100 Receiver Front Panel
Front Panel Controls and Functions
(Fig. E)
32 POWER SWITCH: Press the power switch to turn the receiver
on. After a short power-up sequence, the display shows the
operating frequency and the alert light is illuminated (if no active
transmitters are present on this frequency). The receiver may also
display a system position (i.e., “MASTER”, “SLV-#”) or an
assigned transmitter or receiver name (if this feature has been
set up—the display recalls the setting from the last time power
was applied). Refer to page 13 on setting up receiver names or
page 18 on setting up transmitter names.
33 HEADPHONE OUTPUT: 1/4" (6.3 mm) TRS (“stereo”) phone jack
provides monitoring of the receiver’s output. Plug in either a
mono or "stereo" headphone to monitor receiver signal.
Note: On an operating unit, be careful not to press the Power
switch accidentally when inserting a headphone jack or adjusting
the headphone level. In addition to interrupting receiver operation,
even a momentary loss of power to a single unit within a linked
multi-channel system will cause the loss of linking connection to the
affected receiver and all those “downstream” from it.
34 HEADPHONE LEVEL CONTROL: This control is used to set a
comfortable listening level for the headphone jack; it does not
affect receiver audio output. Turn the control clockwise to
increase the level.
35 ALERT INDICATOR: The alert light illuminates to indicate to the
user that something needs attention; for example, the transmitter
batteries are low, or the transmitter is muted or turned off.
The Alert Indicator lights:
(a) When the receiver is in the Mute mode,
(b) When no RF signal is received from the transmitter,
(c) When only one or two RF signal-strength bars are on,
(d) When the transmitter is in the Mute mode,
(e) When audio modulation level from the transmitter is close to
the clipping point (AF +6 bar), or
(f) When the “LOW BAT” warning appears in the LCD
(transmitter battery is weak).
36 LCD WINDOW: Liquid Crystal Display indicates control settings
and operational readings. It is also used in conjunction with the
Mode/Set and Up/Down arrow buttons to change user-
configurable functions. See Figure G on page 12 for details.
UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R4100
ALERT MODE/SET
POWER ON
OFF
PHONES
IN
OUTPUT
(UNBAL.)
INSTRUMENT
0/-6/-12
ATTN (dB)
BALANCED
MIC OUTPUT
GROUND
LIFT
GROUND IN – LINK – OUT
IN
ANT. A
WARNING:
THIS APPARATUS MUST BE EARTHED.
AC ˜
100V-240V
50/60Hz
MIN– LEVEL –MAX
ANT. B
RX NAME
39 36 32 37 38 33 34 35 39
37 UP/DOWN BUTTONS: Press Up or Down arrow button, in
conjunction with the Mode/Set button, to scroll through the
function menu in Menu mode or through the available choices
for a given function in Edit mode. When the receiver is in
normal operating mode, the Up/Down arrow buttons scroll
through Receiver Address (“MASTER” or “SLV-#”), Receiver
Preset Name, or Transmitter Preset Name.
38 MODE/SET BUTTON: Use in conjunction with the Up/Down arrow
buttons to step through menus, choose operating frequency and
select receiver function options. The Mode/Set button has
different functions depending on the status of the receiver. Two
distinct operations are associated with this button:
Touch: A momentary press of the Mode/Set button. It is used to
enter Menu mode, to enter Edit mode, or to Escape
without making any changes to current settings.
Hold: A press and hold (about two seconds) of the Mode/Set
button. It is used to accept a new setting when the
receiver is in Edit mode or to save the current settings to
one of the five user-defined name presets or the internal
memory location (“NAME?”).
39 MOUNTING ADAPTERS: For mounting the receiver in any
standard 19" rack. Attach to the receiver with the screws
supplied. (Use an optional AT8628a joining-plate kit to mount two
AEW-R4100 receivers side by side.)