Audio-Technica AEW-T1000A - Manual (Page 15)

Artist Elite ® 4000 & 5000 Series Professional UHF Wireless Systems
15
b. To enter a custom name for a Preset:
b1. At the desired choice, hold the Mode/Set button. The first
character blinks.
b2. Using the Up or Down arrow, move through the available
characters (see box below) until the desired character is
reached. Touch an arrow button for single steps, or hold it
down to scroll through the characters at increasing speed.
b3. Touch the Mode/Set button once to accept the first
character and move to the second character, which now is
blinking. Use an Up/Down arrow button to find the desired
second character; touch the Mode/Set button once to
accept it and move to the third position. Repeat this
selection process until the character for the sixth position
has been selected.
b4. Once the sixth character has been selected as desired,
hold the Mode/Set button until “STORED” appears in the
window. This stores the custom Name with the associated
function choices and returns the unit to normal operation.
The display shows the custom name in the top line.
Note: If a correction or change is desired while entering characters,
simply touch the Mode/Set button once when the sixth (last)
character has been reached. The window will flash “ESCAPE.” Touch
the Mode/Set button once more to start the name-entry process over
at the first character. (To leave any characters as they are, simply
touch Mode/Set once to skip over them.)
Available receiver Name character choices:
A …through… Z,
__ (underscore) … (space) …
[ (left bracket) … ] (right bracket),
* … + … -- … / ,
0 …through… 9,
| … < … > … ?
To load (recall) a Preset:
1. Touch the Mode/Set button once to move to Menu mode.
2. Touch the Up arrow twice. LCD top line shows “PRESET.”
3. Touch the Mode/Set button once. “LOAD” (or “STORE”) appears
in the LCD.
4. If needed, touch the Up arrow once to change the selection
to “LOAD.”
5. Hold the Mode/Set button. The name of the currently loaded
Preset appears on the second line of the LCD.
6. Touch the Up or Down arrow to cycle through the available
choices, stopping on the desired choice.
7. Hold the Mode/Set button until “LOADED” appears briefly in
the LCD. The receiver reverts to normal operation with the
selected preset’s functions loaded. The top display line indicates
the loaded preset and the bottom line the current frequency.
To revert to factory-default values:
1. Touch the Mode/Set button once to move to Menu mode.
2. Touch the Up arrow twice. “PRESET” shows in the LCD window.
3. Touch the Mode/Set button once. “LOAD” (or “STORE”) appears
in the LCD.
4. Touch the Up arrow once, if needed, to change the selection
to “LOAD.”
5. Hold the Mode/Set button. The name of the currently loaded
Preset appears on the second line of the LCD.
6. Touch the Up/Down arrow buttons to cycle through the available
choices until “DEF” appears in the display.
7. Hold the Mode/Set button to load the factory default settings.
“LOADED” appears briefly in the LCD. The receiver then reverts
to normal operation at factory-default values. “DEF” appears in
the upper line of the LCD.
Note: Loading the default setting will also revert the receiver
frequency to the lowest frequency in the band.
Table 1 Receiver Functions
Function
Menu Default
Value Choices
(Edit)
▲▼
Wrap-
around*
▲▼ Frequency Lowest in band up to 996
discrete
frequencies
Yes
▲▼ Scan**/*** No value Scan start –
▲▼ Lock NO.LOC NO.LOC ALL.
LOC PC.LOC
RX.LOC Yes
▲▼ Antenna**
Power
OFF OFF
ON Yes
▲▼ Squelch - (one bar) 15 steps,
2 dB each No
▲▼ Meter NORMAL NORMAL
HOLD Yes
▲▼ Preset PRESET Press once,
then select
LOAD or
STORE Yes
▲▼ LOAD: DEF DEF (default),
PRSET1
through
PRSET5 Yes
▲▼ STORE: PRSET1 PRSET1
through
PRSET5 Yes
▲▼ Quit
(exit Menu)
QUIT Press Mode/
Set once to
exit –
* Continue in the same Up/Down direction and choices
“wrap around” to the other end of the range.
** AEW-R5200: Scan and Antenna Power selections in LCD
menu on Channel 1 only.
***Scan selection is not available when the receiver has been
linked as a slave unit.