Audio-Technica AEW-T1000A - Manual (Page 12)

Artist Elite ® 4000 & 5000 Series Professional UHF Wireless Systems
12
UHF SYNTHESIZED DIVERSITY RECEIVER AEW-R4100
ALERT
MODE/SET
POWER ON
OFF
PHONES
IN
OUTPUT
(UNBAL.)
INSTRUMENT
0/-6/-12
ATTN (dB)
BALANCED
MIC OUTPUT
GROUND
LIFT
GROUND IN – LINK – OUT
IN
ANT. A
WARNING:
THIS APPARATUS MUST BE EARTHED.
AC ˜
100V-240V
50/60Hz
MIN– LEVEL –MAX
ANT. B
RX NAME
42 47 44 43 45 46 48 41 40
RX NAME
RX LOCK
TX LO
TX HI
TX LOCK
TX NAME
49 51 53 58 59 52 57
50 54 55 56
Receiver Controls and Functions (Continued)
Fig. F AEW-R4100 Receiver Rear Panel
Rear Panel Controls and Functions
(Fig. F)
40 ANTENNA INPUT JACK: BNC-type antenna connector for Tuner
“B.” Attach the antenna directly, or extend it with a low-loss
antenna cable. See the “Antennas” section on page 7 for more
details.
41 INSTRUMENT OUTPUT JACK: 1 /
4
" phone jack. Can be connected
to an aux-level input of a mixer, guitar amp or tape recorder. On
the AEW-R4100, this is an unbalanced TS phone jack.
42 AF OUTPUT ATTENUATOR: Three-position switch adjusts audio
output level of both audio output jacks with attenuation of 0 dB,
–6 dB or –12 dB.
43 MIC OUTPUT JACK: XLRM-type connector. A standard
2-conductor shielded cable can be used to connect the receiver
output to a balanced microphone-level input on a mixer or
integrated amplifier.
44 GROUND LIFT SWITCH: Disconnects the ground pin of the
balanced output jack (43) from ground. Normally, the switch
should be to the right (ground connected). If hum caused by a
ground loop occurs, slide switch to the left (ground lifted).
45 LINK IN JACK: Connect provided cable to this jack with the index
mark on the plug aligned toward the screw head above the jack.
The receiver with a Link In and no Link Out connection is the
“Master” unit.
46 LINK OUT JACK: Connect provided cable to this jack with the
index mark on the plug aligned toward the screw head above the
jack. The receiver with a Link Out and no Link In connection is the
last unit in a multi-unit system.
47 ANTENNA INPUT JACK: Connector for Tuner “A.” Attach the
antenna directly, or extend it with a low-loss antenna cable.
48 AC POWER INPUT: IEC-type connector for 100V–240V AC,
50/60 Hz power input. No adjustment for mains voltage/
frequency is necessary.
49 RF SIGNAL LEVEL INDICATOR: Shows the strength of the RF
signal received from the transmitter. Also indicates which Tuner
(A or B) has the better reception and is in operation. When the
METER HOLD function is on, the lowest-level RF signal received
from the transmitter is indicated by a flashing bar.
50 ALPHANUMERIC DISPLAY: Shows Receiver Name (57),
Transmitter Name (57), or Link Address (MASTER, or SLV and the
slave number). The factory setting displays “DEF” in Receiver
Name mode (“RX NAME”). Once the settings have been
changed, the unit will display the last setting and mode selected.
Also flashes the “LOW.BAT” warning when the associated
transmitter’s batteries are weak.
Fig. G Receiver LCD Window
51 TRANSMITTER BATTERY INDICATOR: Displays a maximum of
four bar segments, with four bars indicating full power.
52 FREQUENCY DISPLAY: Indicates the current frequency setting
in MHz.
53 “EDIT”: Appears and flashes when the receiver is in edit mode.
54 TRANSMITTER RF POWER DISPLAY: Indicates either “TX LO”
or “TX HI”.
55 “TX LOCK”: Appears when the transmitter is in one of its three
lock settings (ALL.LOC, MUT.LOC or PWR.LOC).
56 “RX LOCK”: Appears when the receiver is in one of its three lock
settings (ALL.LOC, PC.LOC or RX.LOC).
57 TX/RX NAME: Indicates whether the transmitter name or the
receiver name is displaying in the top line of the LCD display.
58 “MUTE”: Appears when the receiver or transmitter is muted,
when the receiver is not receiving an audio signal, or when the
receiver is externally muted by use of the EXTERNAL MUTE jack.
59 AF LEVEL INDICATOR: Shows the audio modulation level of
the received signal. When the METER HOLD function is on, the
bar corresponding to the highest level reached will stay lit.