Audio-Technica AEW-T1000A - Manual (Page 22)

Artist Elite ® 4000 & 5000 Series Professional UHF Wireless Systems
22
Note: The top line of the LCD indicates when frequencies belong to
IntelliScan groups. Asterisks (*) are displayed in front of “FRQ” to
indicate membership in one of more of the three groups (
Figure R ).
See page 25 for frequency group listings.
7. When finished entering a frequency, press the Up arrow button
once. The display reads “QUIT.”
There are several ways to quit, depending on whether the current
Name is to be retained or the frequency stored to a user preset.
See page 13 for help with Quitting and saving changes.
To quickly store the new frequency into the “NAME?” location,
touch the Mode/Set button. The receiver shows “NAME?” in the
top line and the new frequency in the bottom line.
Note: You must now set the transmitter to the exact same frequency
for the system to operate (see page 23).
FIG. R
Note: An asterisk in two or more locations indicates this frequency is
in more than one group.
Setting Receiver Frequency Using IntelliScan™
Single-receiver systems (either an AEW-R4100 or
an AEW-R5200): Turn down the AF level of the associated mixer
or amplifier.
Make certain that any AEW transmitters are turned off. (Other
RF-generating devices in the area should be turned on, if possible.)
1. Touch the Mode/Set button once to enter the Menu mode. (On
an AEW-R5200, use Channel 1 to perform the IntelliScan for
both channels.)
2. Touch the Down arrow once. The display shows “SCAN.”
3. Hold the Mode/Set button to start the scan. The second line
displays “------” during the scan and then briefly displays “SCAN
OK” when the scan is successfully completed.
4. The display on the receiver then shows “RESET NAMES.” The
receiver remains in this state (system is muted) until one of the
following steps is completed:
a. To accept and use this frequency with the currently loaded/
named preset, touch the Mode/Set button. The LCD briefly
displays “STORED” and reverts to normal operation. At this
point, the display shows the receiver name/preset currently
loaded. ( Note: This frequency is now stored with the
associated named preset and is recalled when that preset
is reloaded.)
Group 1
Group 2
Group 3
b. To accept and use this frequency and store it in the special
“NAME?” location, hold the Mode/Set button. The LCD
displays “NAME?” on the top line. ( Note: Doing this allows
a new frequency to be used without affecting previously
stored preset data. However, the receiver shows “NAME?”
instead of the preset’s name.) To store this frequency
along with other settings into one of the user presets, refer
to the instructions on page 13.
IMPORTANT! If one of the above steps (a or b) is not completed,
the receiver will remain in the “RESET NAMES” state indefinitely
(system is muted), and it will not automatically back out to normal
operating mode.
Multiple-receiver systems: Turn down the AF level of the associated
mixer or amplifier. Make certain that any AEW transmitters are turned
off. (Other RF-generating devices in the area should be turned on,
if possible.)
1. Make certain all the receivers are connected (daisy-chained) with
link cables. The receiver with only a Link In (no Link Out
connection) becomes the Master receiver. (See “Link
connections” on page 8.)
2. Switch on all the slave receivers first; switch on the Master
receiver last. Alternatively, all receivers can be turned on
simultaneously, as when using AC power plug strips controlled by
a single AC switch. (If an AC power or link connection is
interrupted, even briefly, all receivers must be turned off and the
power-up sequence repeated to assure complete system control.)
3. Using controls on the Master receiver, follow all the steps listed
for single-receiver systems to assign compatible frequencies for
all receivers by using IntelliScan.
4. The display on the Master shows “RESET NAMES”, and the
display on each slave shows “SCAN” and the new frequency.
The receivers remain in this state (system is muted) until one of
the following steps is completed to accept the new frequency plan:
a. To accept and use this frequency plan with the currently
loaded/named presets, touch the Mode/Set button. If a user
preset was previously loaded on the receiver, the LCD briefly
displays “STORED” and reverts to normal operation. The LCD
then displays the previously loaded user preset or receiver
name and the new frequency. ( Note: This frequency is now
stored with the associated named preset and is recalled when
that preset is reloaded.) If no user preset was loaded (i.e., the
default settings were in effect), the LCD shows “NAME?” and
the new frequency.
b. To accept and use this frequency and store it in the special
“NAME?” location, hold the Mode/Set button. The LCD
displays “NAME?” on the top line. (Note: Doing this allows a
new frequency to be used without affecting previously stored
preset data. However, the receiver shows “NAME?” instead of
the preset’s name.)
To store this frequency along with other settings into one of the user
presets, refer to the instructions on page 13.
Note: These changes affect all linked receivers.
IMPORTANT! If one of the above steps (a or b) is not completed,
the Master and all linked slave receivers will remain in the
“RESET NAMES” state indefinitely (system is muted) and will not
automatically back out to normal operating mode.