Pioneer CNDV-50MT - Manual (Page 92)

90
Cha
p
te
r
8
Cu
st
o
m
is
in
g t
h
e Au
dio
S
o
u
rc
e S
et
tin
g
AV
2
Touch 8 or 2 to adjust front/rear speaker
balance.
Each time you touch 8 or 2 moves the front/
rear speaker balance towards the front or the
rear.
FRONT:15 – REAR:15 is displayed as the
front/rear speaker balance moves from front
to rear.
FR:00 is the proper setting when only two
speakers are used.
When the rear output setting is REAR SP
SUB. W, you cannot adjust front/rear speaker
balance.
➲
Setting the rear output and subwoofer
controller ➞ Page 95
3
Touch 4 or 6 to adjust left/right speaker
balance.
Each time you touch 4 or 6 moves the left/
right speaker balance towards the left or the
right.
LEFT:9 – RIGHT:9 is displayed as the left/
right speaker balance moves from left to right.
Adjusting equaliser curves
You can adjust the currently selected equaliser
curve setting as desired. Adjusted equaliser
curve settings are memorised in CUSTOM.
• You can adjust the centre frequency, level and
the Q factor (curve characteristics) of each
currently selected curve band (LOW/MID/
HIGH).
• BAND:
You can select the equaliser band.
• LEVEL:
You can select the decibel (dB) level of the
selected EQ.
• FREQUENCY:
You can select which frequency to be set as
the centre frequency.
• Q FACTOR:
You can select the details of the curve
characteristics.
1
Touch “EQ MENU” in the AUDIO menu.
2
Touch 4 or 6 to select the equaliser band
to adjust.
Each time you touch 4 or 6 selects equaliser
bands in the following order:
LOW (low) – MID (mid) – HIGH (high)
3
Touch “+” or “–” to adjust the level of the
equaliser band.
Each time you touch “+” or “–” increases or
decreases the level of the equalisation band.
+6 – –6 is displayed as the level is increased
or decreased.
4
Touch 4 or 6 to select the desired
frequency.
Touch 4 or 6 until the desired frequency
appears in the display.
Low: 40 – 80 – 100 – 160 (Hz)
Mid: 200 – 500 – 1k – 2k (Hz)
High: 3.15k – 8k – 10k – 12.5k (Hz)
5
Touch 4 or 6 to select the desired Q
factor.
Touch 4 or 6 until the desired Q factor
appears in the display.
2WIDE – 1WIDE – 1NARROW – 2NARROW
❒
If you make adjustments, CUSTOM curve
is updated.
Adjusting bass and treble
Use this function to adjust the bass and treble.
The ability to select the frequency as well as the
level gives you good control over the tonal
balance of the audio.
The bass and treble adjust screens allow you to
reduce or boost frequencies in the following area;
Bass: 40, 63, 100, 160 (Hz)
Treble: 2.5K, 4K, 6.3K, 10K (Hz)
• If EQ-EX is turned on and CUSTOM is
selected as the equaliser curve, you can adjust
bass and treble settings.
➲ Compensating for equaliser curves (EQ-EX)
➞
Page 92
1
Touch “BASS” or “TREBLE” in the
AUDIO menu.
2
Touch 4 or 6 to select the desired
frequency.
3
Touch “+” or “–” to adjust the bass or
treble level.
Each time you touch “+” or “–” increases or
decreases the bass or treble level. +6 – –6 is
displayed as the level is increased or
decreased.
Au
di
o Adju
st
m
en
ts
MAN-CNDV-50MT-EN.book Page 90 Wednesday, May 4, 2005 1:49 PM