Pioneer BDP-320 User Manual
Page 57
57
En
07
• Pictu
re is stretched.
• Pictu
re is cropped.
• As
pect ratio cannot be
switched.
Is the TV’s as
pect ratio
properly set?
Read the TV’s o
perating instructions and set the TV’s aspect ratio
properly.
Is
TV Aspect Ratio properly
set?
Set
TV Aspect Ratio properly (page 37).
Is
4:3 Video Out properly
set?
Set
4:3 Video Out properly (page 37).
Is
DVD 16:9 Video Out
properly set?
Set
DVD 16:9 Video Out properly (page 37).
When video signals with a
resolution of 1080/50i, 1080/50p, 720/50p,
1080/24
p, 1080/60i, 1080/60p or 720/60p are being output from the
HDMI OUT terminal or the COMPONENT VIDEO output terminals,
they may be out
put with an aspect ratio of 16:9 even if
TV Aspect Ratio
is set to
4:3 (Standard) (page 37).
Pictu
re is interrupted.
The
picture may be interrupted when the resolution of the recorded
video signal switches. P
ress
OUTPUT RESOLUTION to select a setting
othe
r than
Auto or Source Direct (page 21).
The subtitles cannot be
switched.
The subtitles cannot be switched fo
r discs recorded on a DVD or BD
recorder.
Sound and
picture are not
synch
ronized.
Is
Output Terminal properly
set?
Set
Output Terminal properly (pages 18 and 43).
Is
Lip Sync properly set?
Adjust the amount of audio delay with the
Lip Sync setting (page 35).
• No sound is out
put.
• Sound is not out
put
properly.
Is the disc
played back in
slow motion?
Is the disc
played back in fast
fo
rward or fast reverse?
No sound is out
put during slow motion play and forward and reverse
scanning.
A
re the audio cables properly
connected?
• Connect the cable
properly according to the connected devices
(
page 13).
• Inse
rt the cable firmly and all the way in.
Is the audio cable damaged? If the cable is damaged,
replace it with a new one.
A
re the connected
com
ponents (AV receiver or
am
plifier, etc.) properly set?
Read the o
perating instructions of the connected components and
check the volume, in
put, speaker settings, etc.
A
re you trying to listen to the
sound of the
HDMI OUT
te
rminal while watching the
picture from the
COMPONENT VIDEO or
VIDEO output terminals?
Audio signals a
re not output from the
HDMI OUT terminal when video
signals a
re being output from the
COMPONENT VIDEO or VIDEO
out
put terminals. When watching the picture of the
COMPONENT
VIDEO or VIDEO output terminals, connect an optical digital audio
cable o
r regular audio cables to listen to the sound (page 16). Once
connections a
re completed, use
Setup Navigator to make the player’s
settings (
page 18).
Is
HDMI Audio Out properly
set?
Set
HDMI Audio Out to Auto or PCM. (page 38).
Is
Output Terminal properly
set?
When
ANALOG AUDIO is selected at Output Terminal, no audio
signals a
re output from the
HDMI OUT or DIGITAL OUT terminal
(
page 43).
Is the out
put video resolution
properly set?
Use
OUTPUT RESOLUTION to switch to the resolution at which the
video and audio signals a
re output (page 21).
Is a DVI device connected?
The sound will not be out
put from the
HDMI OUT terminal if a DVI
device is connected. Connect the device to a
DIGITAL OUT terminal or
the
AUDIO OUT terminals (page 16).
Fo
r some BDs, audio signals are only output from
DIGITAL OUT
te
rminal or the
HDMI OUT terminal.
Problem
Check
Remedy
320_VXJ5_IBD_EN.book 57 ページ ２００９年２月２５日 水曜日 午前１０時５７分