Pioneer VSX-D510 - Manual (Page 18)

18
En
Displays & Controls
Remote Control
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
SOURCE CLASS MPX BAND
LOUDNESS FUNCTION MUTING
RECEIVER
D.ACCESS
ATT
VOL
MENU
TOP
MENU
VOL
CH
2 DSP MODE MIDNIGHT 5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL EFFECT
ENTER
FQ
FQ
ST ST
FL
DIMMER
REMOTE
SETUP
MASTER
VOLUME
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
TV CONTROL
FUNC
SIGNAL
SELECT
TEST
TONE
RECEIVER TUNER TV CONT
Î
1 2 3 4
5 6 7 8
9 0 10 DISC
CHANNEL
DISPLAY RF ATT
2
6
8
5
1
3
0
9
-
=
!
@
~
#
%
$
^
7
4
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the stated
mode.
For other equipment controls, see Controlling the
Rest of Your System on pages 31-34.
2 RECEIVER button (see page 11)
Use this button when setting up the surround sound
for the receiver.
3 NUMBER/MODE buttons (see pages 25, 31, 33,
34)
Use the number buttons to select the radio frequency
in tuner DIRECT ACCESS mode or the tracks in CD,
DVD mode etc.
Also, buttons marked with the following names have
special functions. If you try to use one of these
functions but the display flashes it means that
function cannot be used in the current mode (for
example DSP modes cannot be used when 5.1 CH
setting is on).
2 (see pages 15, 23)
Use to put receiver in DOLBY DIGITAL, DOLBY
SURROUND and DTS modes. To use first press the
RECEIVER button then operate this button.
DSP MODE (see pages 22)
Use to put receiver in one of the DSP modes. To use
first press the
RECEIVER button then operate this
button.
MIDNIGHT (see page 22)
Use to put receiver in MIDNIGHT mode. To use first
press the
RECEIVER button then operate this button.
5.1 ch (see page 22)
When the DVD/LD or DVD 5.1 CH function is
selected each press switches the DVD/LD input
between DVD/LD and DVD 5.1 CH. To use first press
the
RECEIVER button then operate this button.
CHANNEL SELECT (see page 15-memo)
Use to select a speaker when setting up the surround
sound of the receiver. To use first press the
RECEIVER button then operate this button.
TEST TONE (see page 15)
Use to sound the TEST TONE when setting up the
surround sound of the receiver. To use first press the
RECEIVER button then operate this button.
ATT
If the Overload indicator lights often, use to attenuate
(lower) the level of an analog input signal to prevent
distortion. To use, press the
RECEIVER button first,
then press this button.
CHANNEL LEVEL +/– (see page 15-memo)
Use to set up the levels of the surround sound of the
receiver. To use first press the
RECEIVER button then
operate this button.
SIGNAL SELECT (see page 21)
Use to select the proper signal (analog, digital) for the
source your are inputting. To use first press the
RECEIVER button then operate this button.
* DVD 5.1ch button
Use this button to switch between a DVD player
hooked up to the digital inputs and a 5.1 ch external
decoder hooked up to the 5.1 ch analog inputs.
( DSP MODE button (see pages 20, 22)
Use to switch between the various DSP modes
available (
HALL 1, HALL 2, JAZZ, DANCE, THE-
ATER 1, THEATER 2 ) and DSP off . Use to create
different surround sound effects from any stereo
source.
) SIGNAL SELECT button (see page 21)
Use to select between an analog or digital signal.
_ 2 /DTS button (see pages 20, 21, 23)
Use to switch between the various Dolby/DTS
surround modes.
+ MASTER VOLUME
Use to set the overall listening volume.