Sharp R-1900M - Manual (Page 24)

23
SPLASH COVER (Frame + Cover)
At least once a week, remove the splash cover and wash
both sides of it in a mild detergent solution. A build up of
grease may overheat and begin to smoke and may burn
the splash cover. The splash cover is located in the top of
the oven and may easily be removed. Remember to unplug
the power cord.
SPLASH COVER (Frame + Cover)
Remove the splash cover as shown in Fig. 2 and separate
the frame from the cover.
How to remove the splash cover
Remember to unplug the power cord. Turn the 2 tabs holding
the oven ceiling cover to the oven cavity ceiling as shown
in Fig. 2, then gently pull the cover downwards to separate
from the oven cavity ceiling. Then separate the cover from
the frame. It is held in place by 4 catches.
COVER:
Wipe any grease, spills or spatters on the oven ceiling
cover with a soft cloth dampened with a mild detergent
solution.
Don’t soak the splash cover in detergent or wash it.
FRAME:
Wipe any grease, spills or spatters on the frame with a
soft cloth dampened with a mild detergent solution. Scrape
hardened spills or spatters with a plastic spatula. Don’t
use metallic brushes or sharp-edged tools, as scratches
on the frame may cause the frame to warp or break during
heating. To remove hardened spills or spatters, soak the
frame in a mild detergent solution for a short period of
time. Don’t use detergent with orange oil, as the frame
may melt.
How to install the splash cover
Remember to unplug the power cord. Replace the cover in
the frame. Insert projection A (2) into the 2 holes in the rear
cavity wall and then insert projection B (2) into the 2 holes
in the oven cavity ceiling as shown in Fig. 2. Then slide the
tabs in place.
ANTENNA COVER
If antenna cover has grease, spills or spatters, wipe antenna
cover with a soft cloth dampened with a mild detergent
solution. Don’t use metallic brushes or sharp-edged tools,
as scratches on the antenna cover may cause the cover to
warp or break during heating.
OVEN INTERIOR
Clean the microwave oven cavity, at the end of each day with
a damp soft cloth for hygienic reasons. For heavier soil, use
mild soap applied with a soft damp cloth wipe clean ensuring
all mild soap is removed. Make sure that mild soap or water
does not penetrate through the small vents in the walls which
may cause damage to the oven.
Take care not to let soapy water drip through the small holes
in the oven walls. Excess water spillage throug these holes
will cause damage to the oven interior. It is important that the
door seals and sealing surfaces are kept clean at all times,
wipe regularly with a damp cloth.
The ceramic fl oor should be kept clean at all times. Minor
spills may be wiped with a damp cloth. Do not use abrasive
or harsh cleaners, scouring pads, metallic brushes or sharp-
edged tools. Take care when cleaning to not damage the
silicone seal.
Operating the unit with excessive buildup may result in
cracking or breakage of the ceramic shelf. Do not operate
the unit with a cracked or broken ceramic shelf.
Wipe the door and window on both sides frequently with a
soft damp cloth or sponge to remove any spills or spatters.
Always keep the door seals and seal surfaces clean so that
any grease, spills or spatters are not allowed to build up.
Build-up could result in leakage of microwave energy from
the oven.
OUTER CABINET
Wipe the outside cabinet with a mild detergent solution on
a soft cloth. The control panel must be wiped clean whilst
the door is open, therefore inactivating the oven.
Keep the air intake fi lter clean. Clean the air intake fi lter once
every two weeks (equivalent to 100 hours usage) or more
often for heavy use. See Custom Setting 8 Air Intake Filter
Counter on page 14. Loosen the screw holding the air intake
fi lter to the oven and move the air intake fi lter to the left a
little bit to remove the air intake fi lter from the pin. Wash
the air intake fi lter in mild soapy water, rinse and dry with
a soft cloth. After cleaning and drying completely, re-install
the air intake fi lter.
Do not operate the oven without the air intake fi lter in
place.
NOTES:
1. The screw can be loosened and tightened either by hand
or by using a coin.
2. Install the splash cover properly. Operating the oven with
an incorrectly installed splash cover may damage the
components in the oven cavity and shorten the expected
life span of your oven.
R-1900M [EN].indd Sec1:23 R-1900M [EN].indd Sec1:23 7/4/09 9:50:07 AM 7/4/09 9:50:07 AM