Bryant DuraPac Series 580f - Manual (Page 8)

— 8 —
Table 1 — Physical Data
LEGEND
*Evaporator coil fin material/condenser coil fin material. Contact your local rep-
resentative for details about coated fins.
†Weight of 14-in. roof curb.
**Single phase/three-phase.
††Rollout switch lockout is manually reset by interrupting power to unit or reset-
ting thermostat.
||California rated three-phase high heat models.
***Three phase standard high-heat models have heating input values as shown.
Single phase standard high heat models have one-stage heating with heating
input values as follows:
580FJV036115 — 115,000 Btuh
580FJV048150 — 150,000 Btuh
580FJV060150 — 150,000 Btuh
†††California SCAQMD compliant Low NO
x
models have combustion products
that are controlled to 40 nanograms per joule or less.
UNIT SIZE 580F 036 048 060 072 073
NOMINAL CAPACITY (tons) 3 4 5 6 6
OPERATING WEIGHT (lb)
Unit
Al/Al* 460 470 490 565 615
Al/Cu* 465 476 497 576 —
Cu/Cu* 468 482 505 587 —
Economizer
EconoMi$er+ 50 50 50 50 50
Roof Curb† 115 115 115 115 115
COMPRESSOR Reciprocating Scroll
Quantity 1 1 1 1 1
No. Cylinders (per Circuit) 2 2 2 2 2
Oil (oz) 50 50 50 54 60
REFRIGERANT TYPE R-22
Expansion Device Fixed Orifice Metering Device
Operating Charge (lb-oz)
Circuit 1 4-4 6-6 6-14 9-0 11-0
Circuit 2 — — — — —
CONDENSER COIL Enhanced Copper Tubes, Aluminum Lanced Fins
Rows...Fins/in. 1...17 2...17 2...17 2...17 2...17
Total Face Area (sq ft) 8.36 8.36 10.42 10.42 16.5
CONDENSER FAN Propeller Type
Nominal Cfm 3500 4000 4000 4000 4100
Quantity...Diameter (in.) 1...22.0 1...22.0 1...22.0 1...22.0 1...22.0
Motor Hp...Rpm 1 /
4
...1100 1 /
4
...1100 1 /
4
...1100 1 /
4
...1100 1 /
4
...1100
Watts Input (Total) 325 325 325 325 320
EVAPORATOR COIL Enhanced Copper Tubes, Aluminum Double-Wavy Fins
Rows...Fins/in. 2...15 2...15 3...15 4...15 4...15
Total Face Area (sq ft) 4.17 5.5 5.5 5.5 5.5
EVAPORATOR FAN Centrifugal Type
Quantity...Size (in.) Std 1...10 x 10 1...10 x 10 1...11 x 10 1...10 x 10 1...10 x 10
Alt 1...10 x 10 1...10 x 10 1...10 x 10 — —
High-Static 1...10 x 10 1...10 x 10 1...11 x 10 1...10 x 10 1...10 x 10
Type Drive Std Direct Direct Direct Belt Belt
Alt Belt Belt Belt — —
High-Static Belt Belt Belt Belt Belt
Nominal Cfm 1200 1600 2000 2100 2100
Maximum Continuous Bhp Std .34 .75 1.20 2.40 2.40
Alt 1.20 1.20 1.30/2.40** — —
High-Static 2.40 2.40 2.90 2.90 2.90
Motor Frame Size Std 48 48 48 56 56
Alt 48 48 56 — —
High-Static 56 56 56 56 56
Nominal Rpm High/Low (Direct Drive) Std 860/800 1075/970 1075/970 — —
Alt — — — — —
High-Static — — — — —
Fan Rpm Range Std — — — 1070-1460 1070-1460
Alt 685-1045 770-1175 8778-1192 — —
High-Static 1075-1455 1075-1455 1300-1685 1300-1685 1300-1685
Motor Bearing Type Ball Ball Ball Ball Ball
Maximum Allowable Rpm 2100 2100 2100 2100 2100
Motor Pulley Pitch Diameter Min/Max (in.) Std — — — 2.8/3.8 2.8/3.8
Alt 1.9/2.9 1.9/2.9 2.4/3.4 — —
High-Static 2.8/3.8 2.8/3.8 3.4/4.4 3.4/4.4 3.4/4.4
Nominal Motor Shaft Diameter (in.) Std 1 / 2
1 / 2
1 / 2
5 / 8
5 / 8
Alt 1 / 2
1 / 2
5 / 8 — —
High-Static 5 /
8
5 /
8
5 /
8
5 /
8
7 /
8
Fan Pulley Pitch Diameter (in.) Std — — — 4.5 4.5
Alt 4.5 4.0 4.5 — —
High-Static 4.5 4.5 4.5 4.5 4.5
Belt, Quantity...Type...Length (in.) Std — — — 1...A...40 1...A...40
Alt 1...A...34 1...A...34 1...A...39 — —
High-Static 1...A...39 1...A...39 1...A...40 1...A...40 1...A...40
Pulley Center Line Distance (in.) Std — — — 14.7-15.5 14.7-15.5
Alt 10.0-12.4 10.0-12.4 14.7-15.5 — —
High-Static 10.0-12.4 10.0-12.4 14.7-15.5 14.7-15.5 14.7-15.5
Speed Change per Full Turn of Std — — — 80 80
Movable Pulley Flange (rpm) Alt 48 70 80 — —
High-Static 65 65 60 60 60
Movable Pulley Maximum Full Turns Std — — — 5 5
From Closed Position Alt 5 5 6 — —
High-Static 6 6 5 5 5
Factory Setting Std — — — 3 3
Alt 3 3 3 — —
High-Static 3 1 /
2
3 1 /
2
3 1 /
2
3 1 /
2
3 1 /
2
Factory Speed Setting (rpm) Std — — — 1226 1226
Alt 829 932 1035 — —
High-Static 1233 1233 1416 1416 1416
Fan Shaft Diameter at Pulley (in.) 5 /
8
5 /
8
5 /
8
5 /
8
5 /
8
Al — Aluminum
Bhp — Brake Horsepower
Cu — Copper