MTS SWIFT 50 GLP Sensor Heavy Trucks - Manual (Page 90)

DESCRIPTION
THE INFORMATION AND DESIGN(S)
DISCLOSED HEREIN ARE CONFIDENTIAL
AND THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY
FORM EXCEPT AS GRANTED IN WRITING
BY MTS SYSTEMS CORPORATION. THIS
RESTRICTION EXCLUDES INFORMATION
THAT IS IN THE PUBLIC DOMAIN OR
WAS LEGITIMATELY IN THE PRIOR
POSSESSION OF THE RECIPIENT.
PROPRIETARY DATA
SOURCE/REF
DRAWING
MATERIAL DESCRIPTION
MATERIAL SIZE
FINISH MASK
M
THREAD DEPTHS ARE TO MIN FULL THDS
DRILL DEPTHS ARE TO FULL DIA
REMOVE BURRS AND SHARP EDGES
DO NOT SCALE PRINT
SCALE
MACHINED
SURFACES
180
UNLESS OTHERWISE SPECIFIED
.XXX HOLE SIZE TOLERANCE
0.000
TO .750
+.010/-.002
OVER .750
TO 1.500
+.015/-.003
2 ANGLE
G
E
N
E
R
A
L
T
OL
E
R
A
N
C
E
S
X
Y
.X
.XX
.XXX
THIRD
ANGLE
PROJ
C
MTS SYSTEMS CORPORATION
1/4
EDEN PRAIRIE, MINNESOTA U.S.A.
.1
.03
.010
DRAWN CHECK ENGR
DATE
MFG
DATE DATE DATE
SIZE
TITLE
NEXT LEVEL
PRODUCT CODE
NUMBER
SHEET OF
REV
D
REVISIONS
DATE ENGR DRAWN L
E
T
T
E
R
E
C
N
N
O
m
6
5) ATTACH COVER (ITEM 4) TO BOX. APPLY RTV TO GROOVE AND CONNECTOR AS SHOWN.
APPLY LOCTITE 222 AND TORQUE TO 7 IN-LBS.
APPLY LOCTITE 222 AND TORQUE TO 9 IN-LBS.
BACKSHELL, AROUND (4) COVER SCREW HOLES AND TOP GROOVES OF CABLE ACCESS SLOT.
NOTES:
1) ATTACH PWB (ITEM 2) TO CONNECTOR (ITEM 3). SOLDER PCB PIN CONNECTIONS AND
CABLE CONNECTIONS PER SHEET 2 WIRING SCHEMATIC.
2) APPLY K250 HIGH TEMPERATURE TAPE TO PWB. PLACE ONE BAND (1 INCH WIDE) OVER
CONNECTOR SOLDER CONNECTIONS AND ANOTHER OVER CABLE SOLDER CONNECTIONS.
3) ASSEMBLE PWB & CONNECTOR TO BOX (ITEM 1). PRIOR TO, APPLY RTV TO CONNECTOR,
FILL BOARD MOUNTING HOLES AND APPLY LAYER OF RTV IN CABLE ACCESS SLOT ON BOX
AS SHOWN. REMOVE ANY EXCESS RTV AFTER INSTALLING.
4) APPLY RTV ALL AROUND OUTSIDE EDGE OF BOARD,OUTSIDE EDGE OF THE CONNECTOR
7
B
RLJ - BAO -
3-31-09 - 4-09 -
1 2
-
-
-----
-----
-----
1/1
-
-
574462-XX
FROM: 6, TO: 4.
BOX, MDM, SWIFT 50GLP
B
6-12-12 RLJ RLJ
CABLE ASSY-MODULE
-05 & -06 TO REV B.
UPDATE DOCUMENT REV.
CHANGE ITEM 5 QTY
5
0
0
0
0
1 0
4
8
6
1
2
3
RTV INSIDE GROOVE
4
4
6
RTV AROUND (4) COVER SCREWS HOLES
5
4
7
APPLY RTV TO AREA
(THIS SIDE & OPP. SIDE)
APPLY RTV TO GROOVE AND TOP OF CONNECTOR
2
7 8
1 25
12
1
13
1
11 14
9 10
(INSTALL FROM THIS SIDE)
LENGTH
(SEE TAB ON SHT 2)
A
A
FLANGE BEFORE INSTALLING
TO PROVIDE PROPER SEALING
APPLY RTV TO BOTH SIDES
AND BOTTOM OF CONNECTOR
NOTE THE ORIENTATION
OF CONNECTOR DOVETAIL
SEAL WITH RTV (4 PLACES)
RTV AROUND CABLE EXIT
SECTION A-A
RTV GROOVES