Document Outline

• Important User Information
• Additional Resources
  • Ch 1 - Introduction
  • Ch 2 - Installation
  • Ch 3 - Communications
  • Ch 4 - Applying Power
  • Ch 5 - Display Screen
  • Ch 6 - Maintenance
  • Ch 7 - Specifications and Dimensions
• Notes:
• Chapter 1
  • Introduction
    • Safety Considerations
• Chapter 2
  • Installation
    • Installation Check List
    • Inspecting and Unpacking
    • Location (Environment)
    • Floor Mounting
      • Figure 1 - Bottom View Floor Mount Dimensions
    • Clearance
    • Bypass Switch
    • Circuit Breaker Recommendations
      • Table 1 - Recommended Branch Circuit Protection
    • Electrical Terminations
    • Accessing Terminations
      • Figure 2 - Top Conductor Entry
    • 3-Wire vs. 4-Wire Configurations
    • 3- Wire Models
      • Figure 3 - ProDySC 3-Wire Configuration
    • 4- Wire Models
      • Figure 4 - ProDySC 4-Wire Configuration.
    • Electrical Terminations and Ratings
      • Figure 5 - Electrical Terminations
• Chapter 3
  • Communications
    • Dry Contacts
      • Figure 6 - Access Cover Location
    • Serial Communications Port
      • Figure 7 - Serial Communications Port
• Chapter 4
  • Applying Power
    • Notes:
• Chapter 5
  • Display Screen
    • Overview
      • At installation time perform the following steps to configure your system:
        • Figure 8 - Home Screen
        • Figure 9 - System Configuration
        • Figure 10 - Touch Screen Calibration
        • Figure 11 - Set System Date and Time
    • Home Screen
      • Figure 12 - Home Screen
      • Table 2 - Home Screen Description
    • System Status
      • Figure 13 - System Status Summary
      • Figure 14 - - System Status Waveforms
      • Table 3 - System Status Description
    • Voltage Sag Events
      • Voltage Sag Log
        • Figure 15 - Voltage Sag Log
        • Table 4 - Voltage Sag Log Description
    • Voltage Sag Detail
      • Figure 16 - Voltage Sag Detail
      • Table 5 - Voltage Sag Detail Description
    • Voltage Sag RMS Voltage Charts
      • Figure 17 - - RMS Voltage Charts
    • Voltage Sag Notification
      • Figure 18 - Voltage Sag Detected
    • System Events
      • Table 6 - System Event Description
      • Informational
      • Auto-Resetting
      • User Attention
      • Manual-Reset
      • Call Service
      • System Event Log
        • Figure 19 - System Event Log
        • Table 7 - System Event Log Description
    • System Event Detail
      • Figure 20 - System Event Detail
      • Table 8 - System Event Detail
      • System Event Notification
        • Figure 21 - System Fault Detection
        • Figure 22 - System Fault Detection - Cleared
    • System Configuration
      • Figure 23 - System Configuration
    • Model Information
      • Figure 24 - Model Information
      • Table 9 - Model Information
      • Run System Tests
        • Figure 25 - System Tests
      • Diagnostics Mode
    • Notes:
• Chapter 6
  • Maintenance
    • Preventative Maintenance
      • Monthly Checks
      • 3-6 Month Checks
        • Table 10 - System Event Table
      • POWER_ON
      • Informational
      • Unit
      • T_FAN_ST
      • Informational
      • Unit
      • T_IN_ST_1
      • Informational
      • Unit
      • T_IN_ST_2
      • Informational
      • Unit
      • T_IN_ST_3
      • Informational
      • Unit
      • EXTERNAL
      • Auto-Resetting
      • Inverter
      • RUN_TO
      • Auto-Resetting
      • Inverter
      • LIM_CYCLE
      • Auto-Resetting
      • Inverter
      • STAT_OT
      • User Attention
      • Static Switch
      • OVERLOAD
      • User Attention
      • Unit
      • DC_OV
      • User Attention
      • Inverter
      • CNTRL_UV
      • User Attention
      • Inverter
      • OUTPUT_UV
      • User Attention
      • Inverter
      • INV_OC
      • User Attention
      • Inverter
      • DC_UV
      • User Attention
      • Inverter
      • OUTPUT_OV
      • Call Service
      • Inverter
      • SYNC_ERR
      • Call Service
      • Inverter
      • CONFIG
      • Call Service
      • Inverter
      • CNTRL_MEM
      • Auto-Resetting
      • Inverter
      • UNBALANCE
      • Call Service
      • Inverter
      • AC_V_CHK
      • Call Service
      • Inverter
      • ROLL_CALL
      • Call Service
      • Unit
      • COM_VER
      • Call Service
      • Unit
      • CNFG_TO
      • Call Service
      • Unit
      • CNFG_ERR
      • Call Service
      • Unit
      • FIRM_TO
      • Call Service
      • Unit
      • FIRM_DIFF
      • Call Service
      • Unit
      • SRL_TO
      • Call Service
      • Unit
      • SRL_DIFF
      • Informational
      • Unit
      • T_INV_TO
      • Call Service
      • Unit
    • Fuse Replacement
    • Fuse Rating Charts
      • Table 11 - Pro DySC Fuse Ratings
    • Transient Voltage Surge Suppressor (TVSS)
    • Circuit Breaker CBI, Safety Interlocks and Stored Energy
• Chapter 7
  • Specifications and Dimensions
    • Table 12 - Technical Specifications 200 A ProDySC
    • Table 13 - Heat Dissipation
    • Approximate Dimensions
      • Figure 26 - 200 A ProDySC Dimensions