Rockwell Automation 1771-SDN DeviceNet Scanner Module Installation Instructions - Manual (Page 12)

Publication 1771-IN014B-EN-P - September 2001
12 DeviceNet Scanner Module Catalog Number 1771-SDN/C
5. Repeat steps 1–3 to set the scanner node address for Channel 2,
using the switchbank labeled “Channel 2”. Adjust the switches to
your desired node address setting.
IMPORTANT
The node address setting for DeviceNet Channel 1 must
not conflict with the node address of any other device on
the network.
Channel 1 and 2 Node Address Channels 1 and 2 Node Address
Node
Address
Switch Position
Node
Address
Switch Position
3 4 5 6 7 8 3 4 5 6 7 8
0 0 0 0 0 0 0 32 1 0 0 0 0 0
1 0 0 0 0 0 1 33 1 0 0 0 0 1
2 0 0 0 0 1 0 34 1 0 0 0 1 0
3 0 0 0 0 1 1 35 1 0 0 0 1 1
4 0 0 0 1 0 0 36 1 0 0 1 0 0
5 0 0 0 1 0 1 37 1 0 0 1 0 1
6 0 0 0 1 1 0 38 1 0 0 1 1 0
7 0 0 0 1 1 1 39 1 0 0 1 1 1
8 0 0 1 0 0 0 40 1 0 1 0 0 0
9 0 0 1 0 0 1 41 1 0 1 0 0 1
10 0 0 1 0 1 0 42 1 0 1 0 1 0
11 0 0 1 0 1 1 43 1 0 1 0 1 1
12 0 0 1 1 0 0 44 1 0 1 1 0 0
13 0 0 1 1 0 1 45 1 0 1 1 0 1
14 0 0 1 1 1 0 46 1 0 1 1 1 0
15 0 0 1 1 1 1 47 1 0 1 1 1 1
16 0 1 0 0 0 0 48 1 1 0 0 0 0
17 0 1 0 0 0 1 49 1 1 0 0 0 1
18 0 1 0 0 1 0 50 1 1 0 0 1 0
19 0 1 0 0 1 1 51 1 1 0 0 1 1
20 0 1 0 1 0 0 52 1 1 0 1 0 0
21 0 1 0 1 0 1 53 1 1 0 1 0 1
22 0 1 0 1 1 0 54 1 1 0 1 1 0
23 0 1 0 1 1 1 55 1 1 0 1 1 1
24 0 1 1 0 0 0 56 1 1 1 0 0 0
25 0 1 1 0 0 1 57 1 1 1 0 0 1
26 0 1 1 0 1 0 58 1 1 1 0 1 0
27 0 1 1 0 1 1 59 1 1 1 0 1 1
28 0 1 1 1 0 0 60 1 1 1 1 0 0
29 0 1 1 1 0 1 61 1 1 1 1 0 1
30 0 1 1 1 1 0 62 1 1 1 1 1 0
31 0 1 1 1 1 1 63 1 1 1 1 1 1